UPlay Today ABT-DXBN-N Скачать руководство пользователя страница 25

Страница: 25 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

FOOTING DETAIL - IN GROUND

GROUND

Upright
or Rail

Upright/Component

Footer

In-ground
Footer

Place brick or
equivalent in the
bottom of all
footings to prevent
post from sinking
into the ground

Footer

SURFACING

Footing Detail for Installations

Requiring Concrete Footers

Instructions:

1. Bolt Footer and Inground Footer

together using (3)M10 x 20mm

(3/4”) BHCS Bolts and

M10 Lock Nuts.

Refer to Hole/Footer Location on
the last page of these instructions.

CONCRETE

45º Ref.

(3) M10 x20mm
( 3/4”) BHCS
Bolts

(3) M10
Lock Nuts

IMPORTANT:

Never install play equipment over hard, unresilient

surfaces such as asphalt, concrete or compacted earth. It is the
owner’s responsibility to ensure the “minimum area required”
contains an appropriate amount of resilient material to cushion
accidental falls.

NOTE:
illustration
depicts 3-1/2”
(89mm) diameter
Upright post.

Installaton of
1-1/4”(32mm)
rails/posts
is identical.

Содержание ABT-DXBN-N


















































































Результаты поиска

Содержание ABT-DXBN-N

Отзывы:

Похожие инструкции для ABT-DXBN-N

Бренды по названию

Популярные бренды

UPlay Today ABT-DXBN-N, Руководство по сборке

Результаты поиска

Содержание ABT-DXBN-N

Отзывы:

Похожие инструкции для ABT-DXBN-N

Бренды по названию

Популярные бренды