UPlay Today ABT-DXBN-N Скачать руководство пользователя страница 24

Страница: 24 / 81

UPLAYTODAY

PLAY SYSTEMS • 800.458.5872 • www.uplaytoday.com

FOOTING DETAIL - SURFACE MOUNT - GROUND

IMPORTANT:

Never install play equipment over hard, unresilient

surfaces such as asphalt, concrete or compacted earth. It is the
owner’s responsibility to ensure the “minimum area required”
contains an appropriate amount of resilient material to cushion
accidental falls.

GROUND

Upright/
Component

(3) Ground

Spikes

Upright/
Component

4lb

Hammer

Footer

SURFACING

Footing Detail for Installations

Placed on Ground Level

Instructions:

1. With Footers in position, secure

each footer to the ground using

(3) ground spikes.

NOTE: A 4 lb. hammer may be

required to drive spikes into

the ground.

Install ground spikes angled
inward as shown in illustration.

NOTE:
illustration
depicts 3-1/2”
(89mm)
diameter
upright post.

Installation of
1-1/4”(32mm)
rails/post
is identical.

Clear area of any debris and grade
to level surface to +/- 2°

SITE PREPARATION

Содержание ABT-DXBN-N


















































































Результаты поиска

Содержание ABT-DXBN-N

Отзывы:

Похожие инструкции для ABT-DXBN-N

Бренды по названию

Популярные бренды

UPlay Today ABT-DXBN-N, Руководство по сборке

Результаты поиска

Содержание ABT-DXBN-N

Отзывы:

Похожие инструкции для ABT-DXBN-N

Бренды по названию

Популярные бренды