United States Stove Company SP1000E, Руководство пользователя

Страница: 153 / 188

CAUTION: Moving parts may cause injury. Do not operate with the side panels or repair panel removed. Do not place hands or fingers in the moving auger area at the bottom of the hopper. Do
not obstruct the combustion air inlet opening at the rear of the appliance. DANGER: Risk of electrical shock. Disconnect power before servicing unit. Route power supply cord away from the
appliance. Keep viewing and ash removal doors tightly closed during operation. Replace glass with 5mm ceramic glass ONLY. IMPORTANT: When the hopper lid is open, the auger will stop.
Close the hopper lid to allow system to operate. Provide a source of fresh air to the room where the appliance is installed. Do not obstruct the space beneath the appliance. Inspect and clean
exhaust vent system frequently in accordance with manufacturer's instructions. This wood heater needs periodic inspection and repair for proper operation. Consult the owner's manual for
further information. It is against federal regulations to operate this wood heater in a manner inconsistent with the operating instructions in the owner's manual. Install and use only in accordance
with the manufacturer's installation and operating instructions. Contact local building or fire officials about restrictions and installation inspection in your area. Do not install in a sleeping room. Do
not connect this unit to a chimney flue serving another appliance. Refer to local building codes and the installation and operating instructions for precautions required for passing an exhaust
venting system through a combustible wall or ceiling. Components required for residential or mobile home installation: Model PL Vent Chimney and Components - 3"/75mm or 4" 100mm
diameter. START-UP / Automatic Ignition - Position damper between 1/2" and 3/4" open. Then press the ON/OFF button. Green power light begins to blink. When the light becomes solid, set
the desired heat level. Damper may need to be adjusted based upon heat level. SHUT DOWN: Press the "OFF" button. Unit will shutdown automatically after fuel burns out and unit cools
down. To be installed as a freestanding space heater with the clearances in the manufacturer’s installation instructions. Not to be installed in any fireplace.
Non-Combustible Floor Protection / Un Protecteur de sol
Non-Combustible
Certified to / Certifié: ASTM E1509-2022 and CAN/ULC S627:2023. For Use in Mobile Homes / Transportable Buildings. For use with 1/4" to 3/8" dia. wood pellet fuel only. Use of other fuels will void warranty.
Appareil de chauffage inséré de combustible solide/de type de boulettes. l'installation dans les maisons mobile / bâtiments transportables. Pour Utilisation avec dec granulés uniquement! L'utilisation d'autres
combustibles annulera la garantie.
MODEL / MODÈLE : SP1000E
DATE OF MANUFACTURE /
DATE DE FABRICATION
SERIAL NUMBER / NUMÉRO DU SÉRIE
2 in (50mm) both sides of exhaust
MOBILIER ET LES AUTRES MATIÈRES COMBUSTIBLES À BONNE DISTANCE DE L'APPAREIL.
Input Rating / Note d'entrée: 5.0 lbs/hr
Tarif Electrique: 115V, 60Hz, 3A
ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with 2020 particulate emissions
standards. 75% efficiency. Tested to ASTM
E2779/E2515 - 1.0 g/hr.
AGENCE DE PROTECTION DE L'ENVIRONNEMENT
Certifié conforme aux normes d'émissions de
particules 2020. 75% d'efficacité. Testé selon ASTM
E2779/E2515 - 1,0 g/h.
Clearances to Combustibles:
Residential and Mobile Home /
Dégagements Combustibles:
Dans Une Résidence ou Une
Maison Mobile
A 1" 25.4mm
B 3" 76.2mm
C 12" 305mm
D 1" 25.4mm
E 3" 76.2mm
227 Industrial Park Rd. • South Pittsburg, TN 37380 •
Phone: 423-403-4031 • Web: www.breckwell.com
Corner / Coin Backwall / Sidewall -
Mur Arriére/Paroi Latérale
DO NOT REMOVE OR COVER THIS LABEL / NE PAS RETIRER OU COUVRIR CETTE ÉTIQUETTE
2 in (51mm)
Canada - 8 in (203mm)
6 in (152mm)
Canada - 18 in (450mm)
Flue
A
B
C
E
D
C
D
854046
R
TOLERANCES
EXCEPT
AS
NOTED
DESCRIPTION
REFERENCE
SCALE
DWN BY
DATE
SIZE REV
TITLE NUMBER
ESTABLISHED 1869
1
OF
1
SHEET
DECIMAL
.XX = 0.03 XXX = 0.010
UNITED STATES STOVE COMPANY
ANGULAR
± 2°
HOLES
± .005"
FINISH
© 2010 United States Stove Company
ALL RIGHTS RESERVED
THE DATA CONTAINED HEREIN IS PROPRIETARY TO U. S.
STOVE COMPANY. THIS DATA SHALL NOT BE DUPLICATED,
TRANSFERRED, MADE AVAILABLE, OR USED BY ANY THIRD
PARTY FOR ANY PURPOSE EXCEPT SPECIFICALLY
AUTHORIZED IN WRITING BY U. S. STOVE COMPANY.
CERTIFICATION PLATE 854046
A B
SP1000E
SEE NOTE
SEH
5/23/23
1:1
SEE NOTE
BY DATE DESCRIPTION REV
REVISION HISTORY
A INITIAL RELEASE 5/23/23 SEH
1
1
2
2
3
3
4
4
A A
B B
HEATER MANUFACTURER INSTRUCTIONS:
ALL PLATES ARE TO BE STAMPED BY THE HEATER MFG. WITH A
FACTORY IDENTIFIER NUMBER ISSUED BY USSC. (i.e. 00000-XX)
WHEN LABEL IS APPLIED TO THE HEATER, IT IS TO BE FIRMLY
PRESSED OVER THE ENTIRE SURFACE TO ENSURE IT PROPERLY
ADHERES TO THE MATING SURFACE OF THE HEATER.
SERIAL & DATE BOX
DETAIL
1.50
.25
0.25 TEXT HEIGHT
0.125 TEXT HEIGHT
12.74
4.25
0.25 TEXT HEIGHT
LABELING VENDOR NOTES:
MATERIAL: FOIL PRESSURE SENSITIVE FILM -
1.6 MIL SOLID SILVER ALUMINUM FOIL MATTE or BRIGHT
WITH PERMANENT ACRYLIC ADHESIVE AND 90# STAY FLAT LINER
FINISH: SILVER BACKGROUND WITH BLACK / RED ARTWORK
(ALL TEXT AND ILLUSTRATIONS) UNLESS NOTED OTHERWISE.
TEXT: ALL TEXT TO BE 0.06 HIGH UNLESS OTHERWISE SPECIFIED
1 INCH SQ. BORDER, LOGS
AND FLAMES ARE TO BE RED
0.25 TEXT HEIGHT
0.125 TEXT HEIGHT
0.125 TEXT HEIGHT