United cool air C13-Series Скачать руководство пользователя страница 17

Страница: 17 / 45

Installation, Operation and Maintenance Manual

C13-Series

Subject to change without notice.

10.20-IM (0818)

INFORMATION

On units with three-phase fan motors,

check for proper blower rotation at start-

up� If they run backwards, interchange two

of the incoming power leads�

Blower Motors

All blower motors are equipped with thermal over- load

protectors�

CAUTION

Open disconnects to unit, as motor will

start when automatic thermal overload

resets�

Blower Speed Adjustment

Blower speed may be changed by adjusting the variable

diameter sheave provided on the blower drive motor�

Sheave may be adjusted by removing the belt and loosening

the setscrew located in the hub of the outer flange. With the

setscrew loosened, the flange may be turned clockwise to

increase blower speed and counter-clockwise to reduce

blower speed

UNIT

EVAPORATOR CFM CONDENSER CFM

2 Ton

800

1600

3 Ton

1200

2000

4 Ton

1600

2500

5 Ton

2000

2900

6 Ton

2400

4000

8 Ton

3200

5200

Figure 10: Fan Capacities

CAUTION

Setscrew must be positioned directly

above a flat section of the threaded sheave

shaft before tightening to hold adjustment�

CAUTION

Reduction of airflow through excessive

external air friction losses, lowered blower

speed operation with dirty filters, or

obstructed air flow may result in excessive

condensation at air outlets, short cycling,

or total unit shutdown due to evaporator

coil icing�

INFORMATION

Verify that the motor current draw does

not exceed the motor nameplate current

by more than 10%�

Blower Motor Lubrication

Motor manufacturers indicate that motors never need re-

lubrication, but if units run continuously, it is recommended

that they be re-lubricated every 5500 hours for 3600 RPM

motors and 10,000 hours for 1800 RPM motors� If unit motors

are run in a cyclical manner, lubrication is recommended

every 5 years�
If the unit has been inactive or in storage for over a year, re-

lubricate before starting�
Use Polyrex EM, Texaco Polystar, Pennzoil Penn #2 or

Chevron SRI #2 lubricant or equivalent in the following

quantities: 0�6 cu� in� or 2 teaspoons, approximately 1 1/2 to

2 handle pumps using a standard grease gun� Keep grease

clean, and do not mix dissimilar greases�
Clean area around fitting. Remove purge plug (only on larger

motors) for greasing, and replace after at least 20 minutes

of operation after greasing� For safety, we recommend re-

lubricating while the motor is stopped�
Rotate the motor by hand as the grease is being applied to

avoid air pockets� Over greasing, either in quantity or speed

of injection, can cause premature bearing failure� Apply the

recommended quantity of grease gradually�

CAUTION

Disconnect power and lockout service

before doing any service or maintenance

to the unit�

Содержание C13-Series














































Результаты поиска

Содержание C13-Series

Отзывы:

Похожие инструкции для C13-Series

Бренды по названию

Популярные бренды

United cool air C13-Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание C13-Series

Отзывы:

Похожие инструкции для C13-Series

Бренды по названию

Популярные бренды