United cool air C13-Series Скачать руководство пользователя страница 19

Страница: 19 / 45

Installation, Operation and Maintenance Manual

C13-Series

Subject to change without notice.

10.20-IM (0818)

Sequence Of Operation

Cooling Sequence Of Operation

1�

Before starting the unit, make sure electrical power

has been turned on for a minimum of 24 hours� This

assures that any liquid refrigerant is “driven” out of the

crankcase�

2�

For water-cooled units, make sure condenser water is

available� Open all shut off valves and make sure all

air is purged from the water circuit� Verify that cooling

tower is functioning, if this is the source of condensing

water supply� Start circulating the water to the water

condenser�

3�

The following sequence is based on the unit being

controlled by a room thermostat� If another control

type is being utilized, reference the instructions for that

device may be required�

a�

Raise thermostat setpoint to highest level�

b�

Set System switch to “OFF” position�

c�

Set Fan switch to the “AUTO” position�

d�

Moving the Fan switch to the “ON” position should

cause the evaporator blower motor to run� Moving

the Fan Switch back to “AUTO” should stop the

blower�

e�

Move the System switch to the “COOL” position�

Slowly lower the thermostat setting to call for

cooling� The evaporator blower should start

(assuming the Fan switch is set to “AUTO”) and the

System No� 1 compressor should start�

f�

On those units with multiple compressors, if the

thermostat setpoint continues to be lowered, the

second compressor should then start�

g�

Set room thermostat at desired space temperature

and the Fan switch to “AUTO” or “ON”� The unit will

cycle as required to maintain conditions�

4�

Chilled water sequence is the same as above, except

compressor activation is replaced by the chilled water

valve function�

5�

Heat pump cooling sequence is the same as above,

except the reversing valve will also be activated when

the compressor cycle is started�

Heating Sequence Of Operation

(Other Than Heat Pump)

1�

The following sequence is based on the unit being

controlled by a room thermostat� If another control

type is being utilized, reference the instructions for that

device may be required�

a�

Lower thermostat setpoint to the lowest level�

b�

Set System switch to “OFF” position�

c�

Set Fan switch to “AUTO” position�

d�

Moving the Fan switch to the “ON” position should

cause the evaporator blower motor to run� Moving

the Fan switch back to “AUTO” should stop the

blower�

e�

Move the System switch to the “HEAT” position�

Slowly raise the thermostat setting to call for

heating� The evaporator blower should start

(assuming the Fan switch is set to “AUTO”) and the

electric heating element will be activated�

f�

On those units with a second stage of electric heat,

if the thermostat setpoint continues to be raised,

the second stage of electric heat should then be

activated�

INFORMATION

NOTE: Units with more than one stage

of electric heat require a two stage heat

thermostat�

g�

Set room thermostat at desired space temperature

and set the Fan switch to “AUTO” or “ON”� The unit

will cycle as required to maintain conditions�

Содержание C13-Series














































Результаты поиска

Содержание C13-Series

Отзывы:

Похожие инструкции для C13-Series

Бренды по названию

Популярные бренды

United cool air C13-Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание C13-Series

Отзывы:

Похожие инструкции для C13-Series

Бренды по названию

Популярные бренды