United cool air C13-Series Скачать руководство пользователя страница 28

Страница: 28 / 45

Installation, Operation and Maintenance Manual

C13-Series

Subject to change without notice.

10.20-IM (0818)

Troubleshooting

WARNING

Turn OFF power to unit before conducting any troubleshooting, unless the tests you are performing require

system operation� Keep hands, clothing and tools clear of electrical terminals and rotating components�

ITEM CODE

PROBLEM

PROBABLE CAUSE

SOLUTION

Control is erratic.

Wired improperly or connections are broken

Check wiring connections against schematic

diagram.

Blower fails to start.

Defective contactor
Overload tripped
Marvel alarm

Repair or replace contactor.
Reset and check cause.
Clear alarm(s) after correcting problem.

Compressor fails to start.

Thermostat set too high
Complete loss of refrigerant charge
Head pressure too high

(high pressure switch open)
PTCR will keep compressor OFF

for 3 - 5 minutes
Low line voltage causing compressor to

overheat and trip on thermal overload

Adjust to desired temperature.
Repair leak and recharge refrigerant system.
Check condenser for obstructions and remove.

Check for the required water flow through the water

regulating valve and the condenser coil. Manually

reset thermostat. With Marvel, turn off alarm and

reset.
Wait for PTCR to cool off. Compressor should start

in 3 - 5 minutes.
Stop unit and troubleshoot power supply and

compressor circuit for low voltage. Please note that

it may take the compressor an hour or more for the

thermal overload to reset itself.

Compressor short cycles.

Drain pan switch open
Low line voltage causing compressor to

overheat
Dry or icy evaporator coil (reduced air flow)
Lack of refrigerant (bubbles in sight glass)
Short cycling of conditioned air

Check if the unit is draining properly.
Check power source for cause of electric variation

of line voltage.
Defrost and clean coil and replace dirty filters.
Check for leak. Repair and recharge the system
Make sure that duct connections are proper for

return air and supply air and ensure that they do not

mix with each other.

NOTE: For operating and troubleshooting instructions for Marvel Controller or

humidifier, refer to specific operating instructions that accompany the unit.

Содержание C13-Series














































Результаты поиска

Содержание C13-Series

Отзывы:

Похожие инструкции для C13-Series

Бренды по названию

Популярные бренды

United cool air C13-Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание C13-Series

Отзывы:

Похожие инструкции для C13-Series

Бренды по названию

Популярные бренды