Unitech MS912+ Скачать руководство пользователя страница 73

Страница: 73 / 91

© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd

MS912+ User’s Manual

Appendix A – Numeric Bar Codes

FULL ASCII ( Code 39 ) NUMERIC TABLE

MIN / MAX LENGTH SETTING PROCEDURE:

STEP 1

- Scan: MIN LENGTH/ MAX LENGTH

STEP 2

- Scan: Two digits from FULL ASCII NUMERIC TABLE

STEP 3

- Scan: MIN LENGTH/ MAX LENGTH

Please note that when Min Length and / or Max Length are enabled, the

scanner will only read bar codes that fall into those length parameters. Bar

codes shorter or longer than specified will not be read. The default lengths for

these are indicated in parentheses under the Min and Max bar codes for each

symbology.

RESET

P023$

Note:

1. The scanner will beep three times as a reminder that a setting is not

yet complete.

2. If you make a mistake, forget a step, etc., Scan RESET to start again.

Содержание MS912+











































































Результаты поиска

Содержание MS912+

Отзывы:

Бренды по названию

Популярные бренды

Unitech MS912+, Руководство пользователя

Результаты поиска

Содержание MS912+

Отзывы:

Бренды по названию

Популярные бренды