Unitech MS912+ Скачать руководство пользователя

Страница: 36 / 91

© 2016 unitech Electronics Co., Ltd. All rights reserved.
unitech is a registered trademark of unitech Electronics Co.,Ltd

MS912+ User’s Manual

3.7.1 CODABAR COUPLING

CODABAR COUPLING

ON OFF*

◆

SET INSERT DATA

INSERT DATA-ON

INSERT DATA-OFF

ABC-Codabar and CX-Codabar have certain rules regarding the Stop

Character of first bar code and the stop character of second bar code while in

conjunction, while Codabar- Coupling is enabled, the data from any two

Codabar bar codes can be coupled into one set of data without any limitations

Between the Stop character of first bar code and the Start characters of second

bar code. The Start and Stop characters associated with each bar code will be

sent.

◆

The data can be any alphanumerics of FULL ASCII Table

(

Appendix B

)

ADJACENT REQUIRED

ON OFF*

If CODABAR ADJACENT is enabled, the scanner will only read two adjacent

Codabar bar codes; a single bar code will not be read.

NOTE:

1. Both ABC-Codabar and CX-Codabar can be enabled together, except when

Codabar-Coupling is also enabled.

2. If ABC-Codabar, CX-Codabar, and Codabar-Coupling are all enabled at the

same time, the scanner will read only Codabar- Coupling, that is,

ABCCodabar,CX-Codabar will be considered coupling formats

SETTING PROCEDURE – SET INSERT DATA

STEP 1

- Scan:

Scan SET INSERT DATA.

STEP 2

- Scan: Scan any combination of alphanumeric characters from FULL

ASCII Table.

(

Appendix B

)

STEP 3

- Scan: SET INSERT DATA..

RESET

P023$

Note:

1. The scanner will beep three times as a reminder that a setting is

not yet complete.

2. If you make a mistake, forget a step, etc., Scan RESET to start

again.

Содержание MS912+











































































Результаты поиска

Содержание MS912+

Отзывы:

Похожие инструкции для MS912+

Бренды по названию

Популярные бренды

Unitech MS912+, Руководство пользователя

Результаты поиска

Содержание MS912+

Отзывы:

Похожие инструкции для MS912+

Бренды по названию

Популярные бренды