background image

Appendix A – Setting Up Network Interfaces 

 

Sageon II Bulk Product Manual 

 

 

PM990-5201-00, Issue 6 

7-4 

*** basic parameters 
Hardware: Ethernet Autodetect 
IP addr 192.168.000.098, no gateway set 
 
***************** Channel 1 ***************** 
Baudrate 09600, I/F Mode 4C, Flow 00 
Port 10001 
Remote IP Adr: --- none ---, Port 00000 
Connect Mode: C0  Disconn Mode: 00 
Flush   Mode: 00 
 
Change Setup  : 0 Server configuration 
                1 Channel 1 configuration 
                7 Factory defaults 
                8 Exit without save 
                9 Save and exit                Your choice ? 
 
5. Select an option on the menu by entering the number of the option in the 

Your choice 

? field and pressing 

Enter

 
6. To enter a value for a parameter, type the value and press 

Enter

, or to confirm a current value, just press 

Enter

 
7. When you are finished, save the new configurations (option 

9

). The unit will reboot. 

7.2.4

 

Server Configuration (Network Configuration) 

These are the unit’s basic network parameters. The following parameters are displayed when you select login into 
the unit: 

 
*** basic parameters 
Hardware: Ethernet Autodetect 
IP addr 192.168.000.098, no gateway set 
 
Select 0 and press Enter to configure the Lantronix Interface Server’s basic parameters  

IP Address 

The IP address must be set to a unique value in your network.  

Note: Lantronix Interface cannot connect to the network if the assigned IP address is already in use by another 
device. 

 

Gateway Address 

The gateway address, or router, allows communication to other LAN segments. The gateway address should be the 
IP address of the router connected to the same LAN segment as the 

Lantronix Interface

Note: 

The gateway address must be within the local network. 

 

Subnet Mask 

A netmask defines the number of bits taken from the IP address that are assigned for the host section. 

 
Note: 

Class A: 24 bits; Class B: 16 bits; Class C: 8 bits. 

 
The 

Lantronix Interface 

prompts for the number of host bits to be entered, then calculates the netmask, which is 

displayed in standard decimal-dot notation when the saved parameters are displayed (for example, 255.255.255.0). 

 

 Lantronix, Inc, 2002, all rights reserved, used herein by permission from Lantronix. 

 
 

Содержание Sageon II














































Отзывы: