Unimax AT320 Скачать руководство пользователя страница 9

24

72

CQ9332A-01-008

Cam 

73

M4×6 GB71-85

Setting screws with groove and conical tip 

74

CQ9332A-01-013

Rack poles 

75

10 GB93-87

Washer 

76

M10×40 GB70-85

Screws with inner hexagonal head slot 

77

M10×35 GB70-85

Screws with inner hexagonal head slot 

78

CQ9332-00-016

Cover 

79

M5×10 GB70-85

Screws with inner hexagonal head slot

9

???

Caution:

If you are using your machine in low temperature, let it run for about 20 minutes at 160 rpm to

warm it up. 

After you have assembled your machine you must remove the anti-corrosion coatings with paraffin oil

from the guides, columns, support, exchangeable gears and pulleys. Then you must lubricate it with proper

lubrication oil or grease.

Control buttons and elements

OPERATION

1.  Transmission cover star-grip wheel 

2. 5 pin power cable 

3. Emergency stop button 

4. Power on control light. Indicating that the 

machine is connected to the power source. 

5. Main switch 

6. Speed/rpm gear selector (lathe). You may

switch gear only if the engine is stopped. 

7.

Longitudinal feed direction switch. 

9. Manual wheel of the longitudinal support. 

10. Milling plate 

11. Manual cross feed wheel of the knife head and

small stand. 

12. Knife head safety and release handle It is used

during tool changing. 

13. Manual wheel for fine longitudinal feed control of

the knife head. 

14. ON/OFF switch of the longitudinal feed. 

15. ON/OFF switch of the cross feed. 

16. ON/OFF switch of the cross feed. 

17. Locking handle of the tip socket. 

18. Tailstock locking handle. 

19. Manual wheel of the tip socket feed control. 

20. Adjusting screw. Used for concentric aligning of

the revolving tip centre with the chuck spindle. 

21. Setting of the drilling/milling head position. 

22. Spindle gear shifting lever. 

23. Drilling/milling head engine switch. 

24. Fine vertical feed of the drilling/milling head. 

25. Manual wheel for drilling/milling head lifting.

Содержание AT320

















Отзывы: