
6
•
Never carry electrical tools and appliances by their power cord. When disconnecting the plug from the
wall outlet, never pull the cable by its cord.
•
Protect the power cable from high temperatures, oils, paint thinners and make sure that the cable is not
hanging over sharp edges.
•
Inspect the power cable regularly. If damaged have it replaced by qualified technician. Inspect extension
cables regularly. If damaged, have it replaced.
•
If you need to use an extension cable, use cable with appropriate power rating. Use only completely
unwound. Inspect extension cables regularly. Damaged cable must be repaired or changed immediately.
•
Before performing any maintenance, repair or adjustment, switch off the main switch and disconnect the
power cable from the wall outlet.
•
Make sure no one may switch you machine incidentally on. Do not keep your fingers close to the main
switch, unless absolutely necessary.
•
If you mount your machine to the work table, release the safety button after installation.
•
Do not use in environments where explosives are stored or used (paint shops, warehouse with
flammables etc.).
•
Do not use in humid environments or if wet.
Rotary tools/machines
•
Always wear suitable work clothing (do not wear loose clothing, ties, jewellery etc.). Long hair must be
covered and tied up behind you head. Do not wear worn out working shoes. Sleeves must be rolled up.
Loose clothing or body parts may get caught by moving machine parts.
•
Do not remove safety covers. Make sure the operating personnel is well-protected.
•
Do not touch or come close with moving machine parts during work. Keep your hands away from moving
and spinning machine parts.
Machining and turning operations
•
Always securely fasten the work piece on the work table using appropriate clamping equipment or vise.
Do not hold the work piece in your hands during work. Use both hands to hold the handles of the
machine/tool.
•
Do not overreach. Maintain stable posture on both legs. That way you will not be thrown out of balance in
case of a reverse impact.
•
Keep your tools clean and sharp.
•
When changing tools or during maintenance, follow safety instructions.
•
To feed or move the work piece use appropriate extension tool.
•
Make sure the work piece complies with required technical parameters and that it is securely fastened.
•
Use extra caution when releasing the work piece from the fastening device.
Drilling
•
Make sure the work piece is properly fastened to the work table and secured against turning during
drilling.
•
Before switching your machine on make sure the chuck is turning in the right direction, based on the
used tool.
27
35
5×25 GB117-86
Conical stud
36
AT320-09-041
Large shifting fork
37
AT320-09-029
Shaft socket
38
AT320-09-030
Stopper screw
39
AT320-09-031
Adjustment socket
40
AT320-09-32
Safety nut
41
AT320-09-001A
Drilling/milling spindle box
42
M8×18 GB79-85
Screw with inner hexagonal head slot
43
JY7124 370W
Motor
44
10 GB97.2-85
Regular washers
45
M10 GB6170-86
Hexagonal nut
46
AT320-09-031
Shifting fork shaft
47
AT320-09-039
Small shifting fork
48
M8×20 GB70-76
Screws with inner hexagonal head slot
49
AT320-09-002
Engine assembly plate
50
M6×20 GB70-76
Screws with inner hexagonal head slot
51
AT320-09-004A
Input shaft
52
AT320-09-005
Flat spline
53
M2×5 GB818-85
Screw
54
40 JB/GQ0251-89
Bearing socket
55
50207 GB277-89
Radial ball bearing
56
17 GB894.1-86
Outer safety ring
57
AT320-09-003A
Double toothed gear
58
60201 GB278-89
Radial ball bearing
59
12 GB894.1-86
Outer safety ring
60
12 GB894.1-86
Outer safety ring
61
32 JB/GQ0251-89
Bearing socket
62
50207 GB277-89
Radial ball bearing
63
AT320-09-015A
Toothed gear
64
AT320-09-016
Socket spacer
65
AT320-09-006
Toothed gear
66
AT320-09-007
Toothed gear
67
AT320-09-017
Middle shaft
68
5×55 GB1096-72
Flat spline
69
60201 GB278-89
Radial ball bearing
70
12 GB894.1-86
Outer safety ring
71
M5×16 GB70-76
Screws with inner hexagonal head slot
Содержание AT320
Страница 12: ...12 21 Drilling milling head...