background image

12

Instructions for the installer

x = not less than the length of the boiler body 
(dimensions in mm); in any case, never less than 1300 mm.
xx = see instructions to the side.

3.4 - HEATING PLANT LOCATION

The boiler must be installed in accordance with the rules and 
regulations in force. 
The room  must be well ventilated with openings having an 
area of not less than 1 / 30 of the floor area of the  boiler room 
with a minimum of 0.5 m².
The ventilation openings must be permanent, communicating 
directly with the outside and be positioned at a level high and 
low in accordance with the regulations in force.
The location of the vents, the supply circuits Fuel, power 
distribution and lighting must comply with the applicable laws 
in force in relation to  the type of fuel used
You should install the boiler as close as possible to connection 
of the chimney. 
To facilitate the cleaning of the smoke circuit in front of the 
boiler, it must have a clear space not less than the length the 
boiler , and in any case, never less than 1300mm and it must 
verify that with the door open to 90 ° the distance between 
the door and the adjacent wall, is at least equal to the length 
burner.
The boiler may be placed directly on the floor, because it has 
a basement. 
However, it is useful to provide a concrete platform, a plan to 
level and able to withstand the weight of the boiler when is 
filled with water. 
When placed on the hoof, this must be have at least a size of 
Q x S (see size tables). 
Once installed, the base must be perfectly horizontal and well 
stable (to reduce vibration and the noise level).

fig. 6

3.3  - HANDLING 

The boiler can be easily handled by lifting hooks 
through holes or higher. 
If for reasons of space was necessary, is 
possible to remove the door to facilitate the 
introduction in the central heating.

3.5  - BURNER

The burners in the service of  boiler INOXIA GJ will be CE 
certified, and in particular comply with: 
- Gas Appliance Directive (90/396/EEC); 
- EMC Directive - Electromagnetic Compatibility (89/336 /
EEC). 
They must also be approved in accordance with the 
specifications: 
- UNI EN 676 - forced draft burners for fuel gas. 
- Efficiency Directive (92/42 EEC) 

3.5.1 - CHOICE OF THE BURNER

A proper selection and the adjustment of the burner are 
fundamental for an optimal operation of the boiler and 
therefore they should be accurate and not underestimated. 
The burner must be chose verifying its field work (fuel flow 
rate - pressure in the combustion chamber) that should 

compatible with similar characteristics declared the boiler
Please note that the pressure drop gas side of the boiler, or 
the back pressure in the combustion chamber, are reported at 
zero pressure at the base of the chimney.
It is appropriate that the burner tube length is not less than 
the minimum stated in the table below, and the flame must 
be developed and adapted to the characteristics of our 
combustion chamber
To exploit all the surface of the heat exchange dead-end, you 
must use burners that are able to provide a flame “long and 
narrow” in every 
operating condition, or even at minimum power in the case of 
setting up two or more stages or modulating. 
Flames too short causing localized overheating the front of 
the furnace and combustion products, not sufficiently cooled, 
take the flue to extreme heat can cause serious damage to 
the generator.

1000

X

XX

XX

600

600

Содержание INOXIA GJ 1000

























































Отзывы: