background image

 
 

 

Maintenance

 

 

 
8-10                                                           

ULVAC CRYOGENICS INCORPORATED

 

CAUTION 

6.

Warm up the cryopump (refrigerator unit). Allow the 15K cryopanel of the cryopump (the 

second stage) and the inside of the refrigerator to warm up to room temperature. It usually 

takes hours for the inside of the refrigerator to warm up. The recommended time

 

is for eight 

hours or more.

     

 

 

  When the cryopump is exposed to the atmosphere while warming up, the charcoal on the 

15K cryopanel could adsorb large amount of moisture and it would bring about extension of 

the regeneration time. Care must be taken to prevent this situation. 

 

For Your Information

 

 

Performing the assisted warm-up procedures described in Section 6.3 of this manual can 

shorten the warm-up time. 

 

Before proceeding to next, make sure that the 15K cryopanel has reached room temperature. 

7.

Connect the helium bottle and the regulator. Replace the air remained between the helium 

bottle valve and the regulator with helium gas as instructed in Section 8.4 – Charging Helium 

Gas.  

Use helium gas with purity of 99.999

 or more. 

8.

Perform decontamination procedures as follows: 

Before proceeding decontamination, prepare the rough pumping system as indicated in Figure 

8-4. A roughing pump with the pumping speed of 20L/min or more and the ultimate pressure of 

10Pa or less is recommended.   

 

 

 

 

 

 

 

 

 

 

 

Figure 8-4    Cryopump Decontamination Procedure (1) 

Charging Adopter

To Roughing Pump

High Purity Helium Bottle

Release helium gas

Charge helium gas

Charging Hose

Compressor Unit

Flexible Hose

Bottle Valve

Low Pressure

High Pressure

Regulator

Cryopump

0

0.5

1

1.

5
2

2.

5

3

3.

5

-0.
1

D-
P

RO

D-
P

RO

V2

V1

V3

RETURN

SUPPLY

Содержание CRYO-U Series











































































































Отзывы: