Ultimaker Original страница 93 Скачать руководство пользователя

Страница: 93 / 109

Step 5: connecting the limit switches

Mounting the electronics circuit board

6.6.5. Step 5: connecting the limit switches

To connect the limit switches, perform the following actions.

Connect the plug of BLACK wired limit switch

to the connector

on the circuit board.
The BLACK wired limit switch

is situated behind a hole in the

BOTTOM plane.

2. Connect the plug of BLACK wired limit switch

to the connector

on the circuit board.
The BLACK wired limit switch

is situated at the TOP of the machine.

3. Connect the plug of RED wired limit switch

to the connector

the circuit board.
The RED wired limit switch

is situated at the BACK of the machine.

4. Connect the plug of RED wired limit switch

to the connector

the circuit board.
The RED wired limit switch

is situated at the FRONT of the machine.

5. Connect the plug of BLUE wired limit switch

to the connector called

FRONT RIGHT on the circuit board.
This BLUE wired limit switch situated at the RIGHT of the machine.

6. Connect the plug of BLUE wired limit switch

to the connector called

FRONT LEFT on the circuit board.
This BLUE wired limit switch situated at the LEFT of the machine.

6.6.6. Step 5: connecting the motors

To connect the motors, perform the following actions:

Connect the plug of X motor to the connector called X motor on the
circuit board.
The X motor is mounted on the BACK plane inside the machine.

2. Connect the plug of Y motor to the connector called Y motor on the

circuit board.
The Y motor is mounted on the LEFT panel inside the machine.

3. Connect the plug of Z motor to the connector called Z motor on the

circuit board.
The Z motor is mounted on BOTTOM panel under the machine.

4. Connect the plug of EXTRUDER-MOTOR to the connector called

EXTRUDER-MOTOR on the circuit board.
The EXTRUDER-MOTOR is mounted on the EXTRUDER outside the
machine

Notice: check the connections you have just made.

Notice: if you have the Ulticontroller, assemble it before going to the
next paragraph. How to assemble the UltiCotroller is described in
chapter 6.7.

Содержание Original














































































































Результаты поиска

Содержание Original

Отзывы:

Похожие инструкции для Original

Бренды по названию

Популярные бренды

Ultimaker Original, Руководство по сборке

Результаты поиска

Содержание Original

Отзывы:

Похожие инструкции для Original

Бренды по названию

Популярные бренды