manualshive.com logo in svg

UE 2W2D, Инструкция по установке и обслуживанию, Страница: 3 / 16

Поделиться
Скачать
UE 2W2D Скачать руководство пользователя страница 3

 

IM_ONE-01 

3

 

www.ueonline.com

WIRING

 

Tools Required

Phillips-head screwdriver
Small slotted screwdriver 

Wire strippers

WARNING:    EXPLOSION  HAZARD  -  DO  NOT  REPLACE  COMPONENTS  UNLESS  POWER  HAS  BEEN  SWITCHED  OFF  OR  THE  AREA  IS  KNOWN  TO  BE  NON-
HAZARDOUS. 

WARNING:  EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-
HAZARDOUS

WARNING:  TO MAINTAIN ENCLOSURE INTEGRITY FRONT DISPLAY SCREWS ARE TO BE TORQUED AT 4 IN-LBS (0.45 N-m) IN END USE APPLICATION.

WARNING:  THE DEVICES SHALL BE PROPERLY GROUNDED IN THE END USE APPLICATION.

WARNING:  LEADWIRES MUST BE RATED 75°C MINIMUM COPPER CONDUCTOR ONLY.

WARNING:  MODEL 2W2D ACCEPTS 12-30 VDC AS ITS POWER SOURCE, DIRECTLY FROM DIGITAL INPUTS TO PLCS, DCSS AND OTHER LOW-POWER DC LOADS. 
THE SWITCHED OUTPUT MAXIMUM LOAD RATING IS 40 mA. (THE UNIT MUST NOT BE CONNECTED DIRECTLY TO A POWER SUPPLY WITHOUT AN APPROPRI-
ATE CURRENT LIMITING LOAD SUCH AS THAT PROVIDED BY A PLC/DCS DISCRETE INPUT.  

OVERLOADING THE SWITCH MAY CAUSE FAILURE.

WARNING:  MODEL 2W3A ACCEPTS 90-130 VAC/VDC AS ITS POWER SOURCE, DIRECTLY FROM DISCRETE INPUTS TO PLCS, DCSS AND OTHER LOW-POWER 
LOADS.  THE SWITCHED OUTPUT MAXIMUM LOAD RATING IS 100 mA.  THE UNIT MUST NOT BE CONNECTED DIRECTLY TO A POWER SUPPLY WITHOUT 
AN  APPROPRIATE  CURRENT  LIMITING  LOAD  SUCH  AS  THAT  PROVIDED  BY  A  PLC/DCS  DISCRETE  INPUT.   

OVERLOADING  THE  SWITCH  MAY  CAUSE 

FAILURE.

WARNING:

  

MODEL 2WLP IS LOOP-POWERED AND OBTAINS POWER FROM THE 4-20 mA LOOP.  THE 2WLP41 SWITCHED OUTPUT MAXIMUM LOAD RATING 

IS 0.6 A @ 140 VDC OR VAC AND 0.3 A @ 280 VDC OR VAC FOR MODEL 2WLP43.  OVERLOADING THE SWITCH MAY CAUSE FAILURE.  

THE SWITCH MUST 

NOT BE CONNECTED DIRECTLY TO A POWER SUPPLY.

WARNING:    FOR  INTRINSICALLY-SAFE  INSTALLATIONS,  PLEASE  REFERENCE  THE  CONTROL  DRAWINGS  (UE  62174-19  NORTH  AMERICA  OR  62174-20 
EUROPE) FOR INTRINSIC SAFETY ENTITY PARAMETERS AND OTHER NECESSARY INFORMATION. UNIT MUST BE WIRED TO AN APPROVED I.S. BARRIER. 
REFER  TO  PAGE  12  FOR  ADDITIONAL  INFORMATION  ON  SELECTING  AN  INTRINSIC  SAFETY  BARRIER.    SUBSTITUTION  OF  COMPONENTS  MAY  IMPAIR 

INTRINSIC SAFETY.

WARNING:  MODEL 4W3A ACCEPTS 90-130 VAC/VDC AS ITS POWER SOURCE.  THE SWITCHED OUTPUT MAXIMUM LOAD RATING IS 10 A, 24-280 VAC AT 
T(amb) 38°C (100°F). DERATE 1.8 A/10°C (18°F).  

OVERLOADING THE SWITCH MAY CAUSE FAILURE.

WARNING:

 

 THE ONE SERIES 8W2D MODEL ACCEPTS 12-30 VDC AS ITS POWER SOURCE.  THE MAXIMUM LOAD RATING FOR EACH SWITCH IS SHOWN IN 

THE TABLE ON PAGE 5.  

OVERLOADING THE SWITCH MAY CAUSE FAILURE.

Remove the four (4) Phillips-head screws holding the faceplate to the enclosure. Gently remove the faceplate module. Exercise caution so that the wires going 
between the sensor and the faceplate module are not damaged or removed. Locate field wires and strip carefully. Insert field wiring per the diagrams on page 4. 
Carefully place the faceplate back on the enclosure and re-attach using the (4) Phillips screws (4 in-lbs or 0.45 N-m).  DO NOT OVERTIGHTEN.

Terminal Block and Torque Details

The 2W2D terminal block is marked “+” and “-”, and includes a chassis ground symbol. These markings indicate the polarity of this polarized switch.  Polarity 
must be observed or the 2W2D will not work, making it necessary to reverse the wiring connections.  The 2W2D is reverse polarity protected, so no damage 
results from miswiring. The 2W2D terminal block accepts 14-22 AWG wiring and the recommended torque is 7 in-lbs.

The 2W3A terminal block is market “~” and “~”, and includes a chassis ground symbol. The 2W3A is a non-polarized switch, so connections can be made to 
either terminal without observing polarity. The 2W3A terminal block accepts 14-22 AWG wiring and the recommended torque is 7 in-lbs.

The 2WLP has two terminal blocks, TB1 and TB2.  TB1 has three positions, two marked with a switch symbol and one marked with a chassis ground symbol. TB1 
terminal block accepts 14-22 AWG wiring and the recommended torque is 3.48 in-lbs. TB2 has two positions marked “4-20+” and
4-20-”.  These markings indicate the polarity of the 4-20 mA analog signal. Polarity must be observed.  TB2 terminal block accepts 14-26 AWG wiring and the 
recommended torque is 4.38 in-lbs.

Содержание 2W2D

















Отзывы:

Нет отзывов