UE 2W2D Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 16

UE 2W2D Скачать руководство пользователя страница 1

IM_ONE-01

1

www.ueonline.com

One Series Electronic Pressure
and Temperature Switches

Discrete Input and Loop-Powered

Models: 2W2D, 2W3A, 2WLP

External Powered

Models: 4W3A, 8W2D

U N I T E D E L E C T R I C
C O N T R O L S

Installation and Maintenance
Instructions

Please read all instructional literature carefully and thoroughly before starting. Refer to the final page for the listing of Recommended
Practices, Liabilities and Warranties.

IM_ONE-01

GENERAL

MISUSE OF THIS PRODUCT MAY CAUSE EXPLOSION AND PERSONAL INJURY. THESE INSTRUCTIONS MUST BE THOROUGHLY READ AND UNDERSTOOD
BEFORE UNIT IS INSTALLED.

WARNING: EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR USE IN HAZARDOUS LOCATIONS.

WARNING: SEE THE PRODUCT NAMEPLATE INFORMATION FOR SPECIFIC AGENCY CERTIFICATIONS APPLICABLE TO YOUR PRODUCT.

2W2D MODELS

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D; CLASS II, DIVISION 2, GROUPS F AND G; CLASS III; CLASS I, ZONE
2 AEx nC IIC T5; CLASS I, ZONE 2 Ex nC IIC T5; OR CLASS I, DIVISION 1, GROUPS A, B, C AND D; CLASS II, DIVISION 1, GROUPS E, F AND G; CLASS III;
CLASS I, ZONE 0 AEx ia IIC T5; CLASS I, ZONE 0 Ex ia IIC T5; WHEN INSTALLED PER DRAWING #A-62174-19 (NORTH AMERICA); OR NON-HAZARDOUS

LOCATIONS ONLY.

THIS EQUIPMENT IS ATEX CERTIFIED SUITABLE FOR APPROPRIATE USE IN GAS ZONE 2 & DUST ZONE 22 APPLICATIONS OR GAS ZONE 0 & DUST ZONE
20 APPLICATIONS WHEN INSTALLED PER DRAWING #A-62174-20 (EUROPE).

0539 DEMKO 03 ATEX 0322281X

0539 DEMKO 03 ATEX 0322281X

II 1 G EEx ia IIC T5

II 3 G EEx nL IIC T5

II 1 D T+ 90ºC

II 3 D T+ 90ºC

-40ºC TAMB. +85ºC, IP66

-40ºC TAMB. +85ºC, IP66

2W3A MODELS

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D; CLASS II, DIVISION 2, GROUPS F AND G; CLASS III; CLASS I, ZONE
2 AEx nC IIC T5; CLASS I, ZONE 2 Ex nC IIC T5; OR NON-HAZARDOUS LOCATIONS ONLY.

THIS EQUIPMENT IS ATEX CERTIFIED SUITABLE FOR APPROPRIATE USE IN GAS ZONE 2 & DUST ZONE 22 APPLICATIONS.

0539 DEMKO 03 ATEX 135585X

II 3 G EEx nL IIC T5

II 3 D T+ 90ºC

-40ºC ≤ TAMB. ≤ +85ºC, IP66

2WLP AND 8W2D* MODELS

(* pending approvals)

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D; CLASS II, DIVISION 2, GROUPS F AND G; CLASS III; CLASS I, ZONE
2 AEx nC IIC T4 CLASS I, ZONE 2 Ex nC IIC T4; OR NON-HAZARDOUS LOCATIONS ONLY.

THIS EQUIPMENT IS ATEX CERTIFIED SUITABLE FOR APPROPRIATE USE IN GAS ZONE 2 & DUST ZONE 22 APPLICATIONS.

0539 DEMKO 03 ATEX 0322281X

II 3 G EEx nL IIC T4

II 3 D T+ 130ºC

-40ºC ≤ TAMB. ≤ +80ºC, IP66

4W3A MODELS

THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C AND D; CLASS II, DIVISION 2, GROUPS F AND G; CLASS III; CLASS I, ZONE
2 AEx nC IIC T4; CLASS I, ZONE 2 Ex nC IIC T4; OR NON-HAZARDOUS LOCATIONS ONLY.

1
2
3
...
»

Содержание 2W2D

















Отзывы:

Нет отзывов