U-Line H-1459 Скачать руководство пользователя страница 8

PAGE 8 OF 8

HEATING ELEMENT REPLACEMENT

The heating element expands and contracts during 

each sealing cycle and will eventually break over 

time. Replace using only Uline heating elements.

Make sure that the machine is turned off 
and the power cord is secured before 
working on the machine. 

 

Any attempt to use elements designed 

for use on another machine or in another 
application may not work properly and 
may cause damage and/or create a 

dangerous situation. Use of non Uline parts 
will void all warranties.

Loosen the two clamp mounting screws and 

rotate  the  roller  knobs  to  rewind  the  Teflon

®

 

onto the roller to expose the heating element. 

(See Figure 9)

Remove the heating element retaining nuts at 

each end of the element (keep for reuse).

Remove  the  old  heating  element  and 

discard.

Inspect the insulator on the lower jaw for signs 

of cracks, pits, burn marks, etc.

If  the  insulation  material  is  worn  replace  it 

before  installing  the  new  heating  element. 

Remove  the  old  insulator  when  necessary, 

clean the area, apply a smooth coating of RTV 

adhesive,  install  the  replacement  insulation 

and  allow  it  to  dry  for  several  hours  before 

installing the new heating element.

NOTE: The heating element has a top 
and a bottom. See Figure 9 for proper 
positioning and installation. 

 

NOTE: The seal jaw assembly is spring-
loaded on left end, fixed on right end. 

 
 

.

2.

.

.

5.

Place the left end of the new heating element 

over the threaded post at the left end of the 

jaw assembly.

Compress  the  left  end  of  the  jaw  (spring-

loaded)  and  place  the  right  end  of  the 

heating element over the fixed threaded post 

on the right end.

Make  sure  that  the  heating  element  is 

positioned  correctly,  is  not  twisted  and  lays 

flat against the lower jaw.

Reinstall the retainer nuts no more than finger-

tight.

Reinstall the lower Teflon

®

 cover.

6.

7.

8.

9.

0.

HEATING ELEMENT INSTALLATION

TOP

SIDE VIEW - HEATING ELEMENT

RETAINER NUT

SPRING LOADED TERMINATION

RETAINER NUT

BROKEN ELEMENT

BARRIER STRIP

NEW ELEMENT

REMOVE OR ROLL UP
LOWER TEFLON ASSY.

PRIOR TO STARTING

1

2

3

USE A SMALL SCREW DRIVER
TO COMPRESS THE TENSION

SPRING DURING INSTALLATION

NOTE:

REPLACE TEFLON

COVER BEFORE USE

Figure 9: Replacing heating element

1-800-295-5510

uline.com

Содержание H-1459









Отзывы: