U-Line H-1459 Скачать руководство пользователя страница 2

PAGE 2 OF 8

TOP LEFT FRONT PANEL:

Bag  Adjust:  Flip  up  or  down  to  rewind  or 

dispense the next bag manually.

TOP RIGhT FRONT PANEL:

Bag  Length  Fine  Adjustment:  Clockwise  for 

longer  bags/counterclockwise  for  shorter 

bags.

Bag  Length  Coarse  Adjustment:  Clockwise 

for  longer  bags/counterclockwise  for  shorter 

bags.

Seal  heat-Time  Adjustment  for  bag  sealer: 

Clockwise  to  increase  heating  time/

counterclockwise to decrease heating time.

Cooling-Time  Adjustment  for  bag  sealer: 

Clockwise  to  increase  cooling  time/

counterclockwise to decrease cooling time.

LOWER BACk PANEL:

Power Switch: Push ON ( I ), push OFF ( O ).

OThER CONTROLS:

Foot Switch: Step on to begin both the heat 

sealing and bag dispensing cycles.

Blower  Air  Flow  knob:  (Top  left  side)  Adjusts 

airflow to open bags.

Pinch  Roller  Lever:  (Right  side)  Opens  and 

closes pinch rollers.

Teflon

®

  Roller  Adjustment  knobs:  (Right  and 

left  sides)  Unroll  or  rewind  the  Teflon

®

  cover 

on the lower sealing jaw assembly.

 

Foot Pedal

Seal temp

Power Cord

Bag Adjust

Air Deflector

Pinch Rollers

Blower Air Flow Knob

Pinch Roller Lever

Door

Roller Knob

Roller Knob

Lower Jaw

Lower Teflon Jaw

Upper Teflon Jaw

Compression Pad

Cool Cycle

Bag Length (Coarse)

Bag Length (Fine)

Front Clamp

+

-

+

-

+

-

+

-

Figure : Parts of the Machine

PARTS OF THE MACHINE

Содержание H-1459









Отзывы: