U-Line H-1459 Скачать руководство пользователя страница 1

PAGE  OF 8

USING THIS MANUAL

READ MANUAL FIRST

IMPORTANT: Please read this manual and 
familiarize yourself with the equipment 

before use. The manual contains valuable 
information about the machine, its 

operation and the packaging materials 
used with it.

SAFETY INFORMATION

This manual contains very important information to 

protect both the operator and the machine. Please 

pay special attention to the SAFETY WARNINGS.

STOP - Alerts you to dangerous situations or 

hazards.

CAUTION - Alerts you to actions and 

situations that may affect the machine and 
its operation.

NOTE - Important information about the 
operation and use of the machine.

 

Please enter the serial number of your machine in 

the space provided above. If service in needed, 

please  be  prepared  to  furnish  both  the  model 

number and serial number.

UNPACK AND INSPECT

Remove all packing materials from the machine. 

Do  not  discard  packing  materials  until  you  are 

sure there is no hidden damage. Find the manual 

and related hardware supplied with the machine. 

Carefully examine the machine for any indications 

of damage that may have occurred in transit.

NOTE: If there is any damage, contact 
ULINE immediately.

Remember that even minor damage on the outside 

of the machine can cause problems with sensitive 

components inside the machine.

 

1-800-295-5510

uline.com

BAG ON A ROLL
SYSTEM

2/2007

Serial number ______________ and voltage 
marked on the ID plate _______VAC

Содержание H-1459









Отзывы: