manualshive.com logo in svg

U-Line H-1459, Руководство пользователя, Страница: 7 / 8

Поделиться
Скачать
U-Line H-1459 Скачать руководство пользователя страница 7

PAGE 7 OF 8

After repositioning, retighten the clamp using 

the same two plastic screws.

Tear off the used Teflon

®

 material below the 

clamp. Replace the roll when there is no more 

usable Teflon

®

.

CAUTION! Never attempt to make heat 

seals without the lower Teflon

®

 cover over 

the heating element and lower sealing jaw.

REPLACING ThE LOWER TEFLON

®

 COVER

To  replace  the  lower  Teflon

®

  cover  roll: 

(See Figure 7)

Loosen  the  two  plastic  clamp  screws  and 

rotate  the  roller  knob  with  one  hand  while 

pulling the trailing end of the Teflon

®

 up with 

the other until the two roller mounting screws 

are visible.

Remove the two screws (use either a magnetic 

or  starter  screwdriver).  keep  the  screws  for 

reuse in mounting the new Teflon

®

 cover roll.

Install  the  new  Teflon

®

  cover  roll  by  passing 

the mounting screws through the two eyelets 

and into the roller. The screws should be snug. 

Do not over-tighten as damage could result.

Rotate  the  roller  knob,  winding  the  Teflon

®

 

cover  onto  the  roller.  Insert  the  free  end 

behind  the  clamp.  To  reduce  waste,  put  as 

little Teflon

®

 beyond the end of the clamp as 

possible.

.

.

.

2.

.

.

REPLACING COMPRESSION PAD

Over  time  the  silicone  rubber  compression  pad 

becomes  brittle  and  pitted  and  needs  to  be 

replaced.

Remove  the  upper  Teflon

®

  cover  by  first 

removing the retaining spring. keep the parts 

for reuse.

Remove  the  nut  and  bolt  retaining  the 

compression pad holder. (See Figure 8)

Peel  off  the  old  compression  pad  and 

clean the area so it’s free of lumps and old 

adhesive.

The  replacement  compression  pad  has  a 

pressure sensitive backing. Carefully remove 

the  backing  paper  and  attach  the  new 

compression pad to the jaw. Be sure that it is 

flat and has no depressions or lumps.

Reinstall  the  upper  compression  pad  holder 

and Teflon

®

 cover. 

 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 

.

2.

.

.

5.

Figure 7: Replacing lower Teflon

®

 cover

Figure 8: Replacing compression pad

Содержание H-1459









Отзывы:

Нет отзывов