Tyco PowerSeries Pro HS3032 Скачать руководство пользователя страница 32

PowerSeries Pro Installation Guide

Table 2-1 SIA quick reference

SIA Feature Programming Section

Comments

Range/Default

Requirement

Exit Time

[005]>[001], option 3

Access to Entry and Exit delays and Bell Time Out for the system.

Range:45- 255
seconds

Default: 60 sec.

Required

(programmable)

Exit Delay Restart

[018], option 7

Opening a Delay zone door after it has already been opened and closed during an
exit delay restarts the exit delay timer.

Default: Enabled

Required

Auto Stay Arm on Un-vacated Premises

[001]>[001]-[248] Zone type 05, 06,09

Function key: Forces the system to arm in Stay mode if the occupant does not exit
the premises after pressing the Away function key.

If no exit after full arm

Default: Enabled

Required

Exit Time and Progress Annunciation/Disable
or Remote Arming

[861]>[001]-[005], option 4

System times and audible exit beeps can be disabled when using the wireless key to
stay arm the system. When away arming, audible exit beeps can not be disabled.

For remote arming (using keyfob), it is possible to program the instant stay arm (no
exit delay). By default this option is OFF.

When arming/disarming with keyfob the bell squawk option shall be enabled.

The Bell shall be tested daily. Alternate option is to have bell squawk enabled for
arming/disarming

Default: Enabled

Allowed

Entry delay(s)

[005]>[001]-[008], options 1 and 2

Access to entry and exit delays and bell time out for the system

Note: Combined entry delay and communications delay (abort window) shall not
exceed 60s.

Range: 30 sec. to 4
min.

Default: 30 sec.

Required

(programmable)

Abort Window for Non-Fire zones

[002]>[001]-[248], option 7 ON

Access to zone attributes, i.e., swinger shutdown, transmission delay and cross zone.
May be disabled by zone or zone type.

Default: Enabled

Required

Abort Window Time - for Non-Fire zones

[377]>[002], option 1

Access to the programmable delay before communicating alarms

Note: Combined entry delay and communications delay (abort window) shall not
exceed 60 seconds.

Range: 00 - 45 sec.

Default: 30 sees

Required

(programmable)

Abort Annunciation

An audible tone is generated when an alarm is aborted during the abort window.

Hard-coded ON

Required

Duress Feature

[*][5]> master code> user 2-95> 5> 2

When this feature is enabled, selected user codes send a duress reporting code to the
central station when used to perform any function on the system. Section [019],
option [6] must be enabled.

Default: N

Required

Cancel Window

[377]>[002], option 6

Access to the communications cancel window. Minimum duration must be 5
minutes.

Range: 005-255

Default: 005

Cancel Annunciation

[308]>[001], option 8

Access to the reporting code for Alarm Canceled.

A Cancel was
transmitted

Default: Enabled

Required

Cross Zoning

[042]>Selection 3, option 002

Enables cross zoning for entire system. Zones can be enabled for cross zoning via
zone attribute option 8 in sections [002][101] - [248].

Programming required

Default: Disabled

Required

Burglary Verification Timer

[005]>[000], option 3

Access to the programmable Cross Zone timer.

Range: 000-255 sec.

Default: 60 seconds

Allowed

Swinger Shutdown for Alarms

[377]>[001], option 1

Access to the swinger shutdown limit for zone alarms.

For all non-fire zones, shut down at 1 to 6 trips.

Default: 2 trips

Required

(programmable)

Swinger Shutdown Enable

[002]>[001] - [248], option 6 ON

Access to swinger shutdown, transmission delay and cross zone attributes. Zone
attribute option 6 (Swinger Shutdown enabled) is ON.

Non-police response
zones

Default: Enabled

Allowed

24-Hr. Auto-verified Fire

[001]>[001]-[248], Zone type 025 ON

Access to 24-Hr. Auto-verified Fire.

Activates if Not restored within the specified time.

Must choose zone type
for application

Required

Call Waiting Cancel

[382], option 4 OFF

Access to the dialing sequence used to disable call waiting. Call waiting string can
be programmed in [304].

Depends on user
phone line

Default: Disabled

Required

System Test:

[*][6] Master Code, option 04

The system activates all keypad sounders, bells or sirens for 2 seconds and all
keypad lights turn on. Refer to user manual.

Walk Test Mode:

[*][8][Installer code][901]

This mode is used to test each zone on the system for proper functionality.

Walk Test Communications

[382], option 2

Enables communication of zone alarms while walk test is active.

Default: Disabled

Walk Test Start/ End Reporting Codes

[308][401], options 1 and 2

Access to the reporting codes for walk test start and end times.

Duress Code

Duress codes function the same as user access codes, except they transmit a duress reporting code when used to perform any
function on the system. Duress codes cannot be used to access [*][5], [*][6] or [*][8] menus.

Duress codes are created by the master user or supervisor users

- 32 -

Содержание PowerSeries Pro HS3032





































Отзывы: