PowerSeries Neo Installation Guide
Figure 1-6 Telephone Line Wiring
Telephone format is programmed in option [350]. Telephone call directions are
programmed in options [311]- [318].
Ground Wiring
Figure 1-7 Ground Installation
Note:
Using an insulated green wire (minimum 22AWG), connect the EGND
terminal on the Corbus and the grounding wire from the building electrical
installation to any of the available holes on the back or side of the metal cabinet.
See the diagram attached to the cabinet for suggested GND point location and
hardware recommendations.
Note:
Wire and installation hardware not included.
Enrollment
All optional modules and devices must be enrolled on the system. During
enrollment, the electronic serial number (ESN) of each device is identified to the
control panel and zones are assigned. A wireless transceiver HSM2HOST or an
RF keypad must be enrolled first before wireless devices can be enrolled.
Enrolling Modules
During automatic and manual enrollment, if an attempt is made to enroll more
than the maximum number of modules, an error tone sounds and a message is
displayed on LCD keypads.
Table 1-5 Module Capacity
Module
HS2016 HS2032 HS2064/
HS2064 E
HS2128/HS2128 E
HSM2108 8 Zone expander
1
3
7
15
HSM2208 8 Output
expander
2
4
8
16
Wireless Keypad:
HS2LCDRF(P)X
HS2ICNRF(P)X
HS2LCDWF(P)(V)X
8
8
8
16
HS2TCHP Touchscreen
Keypad
8
8
8
16
HSM2300 Power Supply 1A 3
3
3
4
HSM2204 4 High-current
Output
1
1
3
4
HSM2HOSTx Transceiver
1
1
1
1
HSM2955
1
1
1
1
Modules can be enrolled automatically or manually using section [902] of
Installer programming.
To confirm that a module has been successfully enrolled, use Installer
Programming section [903].
Enroll Wireless Devices
Wireless devices are enrolled via the wireless transceiver module and Installer
Programming section [804][000].
Auto Enrollment
To enroll a wireless device using this method, press and hold the Enroll button on
the device for 2-5 seconds until the LED lights then release the button. The alarm
panel automatically recognizes the device and the keypad displays a confirmation
message. The device ID and next available zone number are displayed. Press [*]
to accept or scroll to another available zone number. Batteries must be installed
in the wireless device in order to enroll.
Pre-Enrollment
Pre-enrollment is a two step process. The first step requires entering each device
ID ([804][001]-[716]). Every wireless device has an ID printed on the sticker
attached to the device. The format is XXX-YYYY where:
l
XXX identifies the type or model of the device
l
YYYY is a short encrypted ID used by the system to identify the specific
device
Pre-enrollment can be done at a remote location and using DLS/SA. The second
step is to press the enrollment button on the device, usually done on location.
Installer Programming does not have to be entered at this step. Both steps must be
performed in order to complete the enrollment.
Programming Methods
The alarm system can be programmed using the following methods:
Table 1-6 Programming Methods
Method
Description
Procedure
Template
programming
Use pre-defined templates to quickly
apply basic programming and to set up
DLS downloading.
Press [899] at the “Enter
Section” screen.
See Template
Programming below for
details.
DLS
programming
Download and apply programming
using DLS 5 v1.3 for Neo v1.0 panels
and DLS 5 v1.4+ for Neo v1.0 and up
products.
For local DLS, use a PC-
Link cable and laptop
with DLS-5 software
installed.
For remote DLS, use a
telephone line, cellular
network or the Internet.
Installer
programming
Manually program all alarm system
and device options.
Press [*][8][installer
code] while the system is
disarmed.
Viewing Programming
Programming sections can be viewed from any system keypad. The method for
viewing and selecting programming options using LCD, LED and ICON keypads
depends on the keypad type used. See below for specific instructions on
programming with each keypad type.
Generally, programming options are accessed in the following way:
1.
Enter Installer Programming mode ([*][8]).
2.
Navigate to a specific programming section.
3.
Select an option to view or change its programming.
All programming options are numbered and can be accessed by navigating
through the menu (LCD) or by keying in the program section number. For toggle
options, the name of the option is displayed (LCD) or LEDs 1-8 are illuminated
(LED and ICON).
Use the keypad numbers to toggle options on or off. Sections requiring data input,
such as phone numbers, display the full data in fields up to 32 characters long
(LCD). To input data, use the scroll keys to select a character then press the
keypad button corresponding to the number/letter required. Scroll to the next
character and repeat the procedure as needed. Press the [#] key to save changes
and exit the program section.
Minimum Required Programming
Once basic installation of the alarm panel is complete, the following general
configuration options can be set.
- 5 -
