TYAN B5538Y292X4-080PV4HR-BDW Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 142

TYAN B5538Y292X4-080PV4HR-BDW Скачать руководство пользователя страница 84

http://www.tyan.com

84

5.3 Getting Help

Pressing [F1] will display a small help window that describes the appropriate keys
to use and the possible selections for the highlighted item. To exit the Help
Window, press [ESC]

.

5.4 In Case of Problems

If you have trouble booting your computer after making and saving the changes
with the BIOS setup program, you can restart the computer by holding the power
button down until the computer shuts off (usually within 4 seconds); resetting by
pressing CTRL-ALT-DEL; or clearing the CMOS. The best advice is to only alter
settings that you thoroughly understand. In particular, do not change settings in
the Chipset section unless you are absolutely sure of what you are doing. The
Chipset defaults have been carefully chosen either by TYAN

®

or your system

manufacturer for best performance and reliability. Even a seemingly small change
to the Chipset setup options may cause the system to become unstable or
unusable.

NOTE:

The following pages provide the details of BIOS menu. Please be

noticed that the BIOS menu are continually changing due to the BIOS updating.
The BIOS menu provided are the most updated when this manual is written.
Please visit TYAN

®

’s website at

http://www.TYAN.com

for the information of

BIOS updating.

«
...
82
83
84
85
86
...
»

Содержание B5538Y292X4-080PV4HR-BDW















































































































































Отзывы:

Нет отзывов