TYAN B5538Y292X4-080PV4HR-BDW Скачать руководство пользователя страница 48

Страница: 48 / 142

http://www.tyan.com

Attention to 2U 4-Node Users:

Please make sure that at least the first Compute Node has been properly

plugged into the power system before you plug in the AC cord and turn the
power on. It is essential to do so for the system to acquire the system PSU
status.
2.

It is not recommended to plug out all four Compute Nodes at the same

time during maintenance. If possible, please finish it within 5 minutes at room
temperature (25

C). If the maintenance work lasts longer than 5 minutes or

the room temperature is higher than 25

C, please unplug the AC cord first in

order to assure the power system is not in no load operation.

Front Components

Node Cover

HDD

PCBs

FAN

Front Panel
Board

SATA HDD
Board

Содержание B5538Y292X4-080PV4HR-BDW















































































































































Результаты поиска

Содержание B5538Y292X4-080PV4HR-BDW

Отзывы:

TYAN B5538Y292X4-080PV4HR-BDW, Руководство сервисного инженера, Страница: 48 / 142

Результаты поиска

Содержание B5538Y292X4-080PV4HR-BDW

Отзывы: