TYAN B5538Y292X4-080PV4HR-BDW Скачать руководство пользователя страница 24

Страница: 24 / 142

http://www.tyan.com

IPMI LED indication in 1+1 PSU Redundancy

Status

Description

IPMI LED

Both PSU1 and PSU2 are present and the AC
cord is properly connected when the system
powers on.

OFF

If the IPMI LED shows amber solid on, please
check the following:



Is the AC cord properly connected?



Are both PSU1 and PSU2 present?

Amber solid on

NOTE:

If you have checked and cleared the Status 2, and the IPMI LED continues to
show amber solid on, please refer to the Web UI to view the Event Log for
possible solutions.

NOTE:

Node 1 is set to be the master node by default, which can detect the

power status. Users can use the jumpers on the power backplate to change the
master node. The jumper settings are as follows:

Master Node setting

Master

Node

Jumper Setting

Node 1

JP6 (1,2), JP7 (1,2)

Node 2

JP6 (3,4), JP7 (3,4)

Node 3

JP8 (1,2), JP9 (1,2)

Node 4

JP8 (3,4), JP9 (3,4)

Содержание B5538Y292X4-080PV4HR-BDW















































































































































Результаты поиска

Содержание B5538Y292X4-080PV4HR-BDW

Отзывы:

TYAN B5538Y292X4-080PV4HR-BDW, Руководство сервисного инженера, Страница: 24 / 142

Результаты поиска

Содержание B5538Y292X4-080PV4HR-BDW

Отзывы: