manualshive.com logo in svg

TYAN B5538Y292X4-080PV4HR-BDW, Руководство сервисного инженера, Страница: 135 / 142

Поделиться
Скачать
TYAN B5538Y292X4-080PV4HR-BDW Скачать руководство пользователя страница 135

 

 

http://www.tyan.com 

 

135

 

BIOS Temp Sensor 

Name Explanation 

CPU DTS Temp 

Temperature of the CPU Digital Temperature Sensor 

CPU_PECI_Value 

Temperature of the CPU Platform Environment Control 

Interface 

CPU_MOS_TEMP 

Temperature of the CPU MOSFET Area 

PCH_Temp Temperature 

of 

PCH 

Sys_Air_Outlet 

Temperature of the Sys_Air_Outlet Area 

MB_Air_Inlet 

Temperature of the M/B Air Inlet Area 

NOTE:

 If the DIMM slot is not populated, the temp sensor will read “N/A”. 

CPU_DIMM_A0 

Temperature of DIMM A0 Slot 

CPU_DIMM_A1 

Temperature of DIMM A1 Slot 

CPU_DIMM_B0 

Temperature of DIMM B0 Slot 

CPU_DIMM_B1 

Temperature of DIMM B1 Slot 

PSU1 Temp 

Temperature of PSU1 

PSU2 Temp 

Temperature of PSU2 

BIOS FAN Sensor 

Name Explanation 

SYS_FAN_1 

Fan speed of SYS_FAN1 

SYS_FAN_2 

Fan speed of SYS_FAN2 

SYS_FAN_3 

Fan speed of SYS_FAN3 

PSU1 Fan 

Fan speed of PSU1 

PSU2 Fan 

Fan speed of PSU2 

 
 
 

Содержание B5538Y292X4-080PV4HR-BDW















































































































































Отзывы:

Нет отзывов