Twin Eagles TE1BQ36RS Скачать руководство пользователя

Страница: 23 / 38

17 | www.twineaglesgrills.com

USING THE GRILL

OPERATING INSTRUCTIONS

TO LIGHT THE GRILL BURNERS

BEFORE LIGHTING THE GRILL

WARNING

DO NOT ATTEMPT TO LIGHT THE GRILL IF YOU SMELL GAS.

• WARNING:

IT IS CRITICAL THAT THE GAS BURNERS ARE PROPERLY INSTALLED WITH THEIR ORIFICES

INSIDE THE BURNERS AIR SHUTTERS. If not properly installed, gas may leak outside of the burner that

could lead to fire, potential damage to your grill and bodily injury. (Please refer to Page 3 for correct

burner installation).

•

If the unit is LP, thread the regulator on the valve of the cylinder and hand tighten until fully seated. Leak

check the hose and regulator connections with a soap and water solution before operating the grill. (Ref

erence Page 11 for leak test procedure)

•

Inspect the gas supply piping or hose prior to turning the gas ON. If there is evidence of cuts, wear, or

abrasion, it must be replaced prior to use. The replacement pressure regulator and hose assembly must

be the type specified by the manufacturer. The pressure regulator and hose assembly supplied with the

units must be used.

•

Always keep your face and body as far away as possible when lighting.

1. Open the grill hood completely. Do not attempt to light the grill with the hood closed.

2. Open the gas supply shut-off valve.

3. Push in the knob and verify that the hot surface igniter glows. The hot surface igniter's are located inside

the flashtubes above the U-burners. If the igniter does not glow, verify for proper power supply. (Refer

ence Page 12 for electrical requirements).

4. After the glowing is verified, hold the knob pushed-in for 5 seconds then turn the knob counter clockwise

so that all the bezel LEDS are lit. Continue to hold the knob pushed in for 5 seconds until you see or hear a

flame. Then release the knob.

CAUTION:

If ignition does not take place within 5 seconds, turn knob to the OFF position, wait for five minutes

and repeat step 4.

5. Once ignited close the hood to allow the grill to preheat until the Temp. Track displays the desired grilling

temperature range.

ATTENTION:

On initial use, light the grill and let it run for approximately 15-20 minutes to burn off any residue from the

factory

1. Check to be certain that the drip pan is in place and pushed all the way back into the grill.

2. Light the grill burners using the instructions above.

Содержание TE1BQ36RS







































Результаты поиска

Содержание TE1BQ36RS

Отзывы:

Похожие инструкции для TE1BQ36RS

Бренды по названию

Популярные бренды

Twin Eagles TE1BQ36RS, Инструкция по установке, использованию и уходу

Результаты поиска

Содержание TE1BQ36RS

Отзывы:

Похожие инструкции для TE1BQ36RS

Бренды по названию

Популярные бренды