Twin Eagles TE1BQ36RS Скачать руководство пользователя

Страница: 16 / 38

Twin Eagles Service (562) 263-3600 | 10

NATURAL GAS INSTALLATION

A typical natural gas installation is shown below. Make sure that the factory-supplied regulator is used

and installed with the arrow mark on the regulator pointing towards the gas grill. Use only pipe sealants that

are approved for use with natural and LP gases. An installer-supplied gas shutoff valve must be installed in an

accessible location.

Please note, when pressure testing, the following statements must be adhered to:

•

This gas appliance and its individual shutoff valve must be disconnected from the gas supply piping sys

tem during any pressure testing of that system at the test pressures in excess of 1/2 psi (3.5 kPa).

•

This appliance must be isolated from the gas supply piping system by closing its individual manual shutoff

valve during any pressure testing of the gas supply piping system at test pressures equal to or less than

1/2 psi (3.5 kPa).

CAUTION:

PROVIDE ADEQUATE VENTILATION HOLES IN THE ENCLOSURE FOR SAFETY

PURPOSES IN THE EVENT OF A GAS LEAK.

CHECKING / CONVERTING THE REGULATOR

If the gas grill is factory built for natural gas, the regulator supplied is set for 4” water column. The

regulator is convertible to 10 in wc (2.48 kPa) for system LP application. Do not use with a 20-lb LP cylinder.

Make sure that the regulator is set for the correct gas type. To check, remove the brass hex cap. You will find

the conversion plastic pin attached to the cap to the underside of the cap. If the disc (1/2 in. diameter) of the

pin is close to the cap, then the regulator is set for natural gas. If the disc is at the tip of the pin, away from the

brass cap, the regulator is set for system LP application. To convert to natural gas, remove the plastic conver

sion pin and invert and replace it back in a manner such that the disc is close to the brass cap. For both natural

and LP, the maximum inlet pressure is 14 in wc (3.5 kPa).

4.50” MIN CLEARANCE TO

ALLOW LID TO FULLY OPEN

TYPICAL REAR

GAS CONNECTION
INSTALLER SUPPLIED GAS

SHUTOFF VALVE

(MUST BE IN AN ACCESSIBLE

LOCATION)

REGULATOR SET

AT 4” WC (NG)

INSULATING JACKET

TYPICAL BOTTOM

GAS CONNECTION

INSTALLER SUPPLIED

GAS SHUTOFF VALVE

SET TO LP

SET TO NG

Содержание TE1BQ36RS







































Результаты поиска

Содержание TE1BQ36RS

Отзывы:

Похожие инструкции для TE1BQ36RS

Бренды по названию

Популярные бренды

Twin Eagles TE1BQ36RS, Инструкция по установке, использованию и уходу

Результаты поиска

Содержание TE1BQ36RS

Отзывы:

Похожие инструкции для TE1BQ36RS

Бренды по названию

Популярные бренды