Twilight MC-SUP2000H Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 69

background image

Chapter 7 Troubleshooting

- 53 -

Chapter 7 Troubleshooting

Ultrasonic flow meter (energy meter) is designed with perfect self-diagnosis
function.The problems found are displayed in chronological order in the form of
code in the upper right corner of the LCD display.M08 menu can show all the
existing problems in order.
Ultrasonic flowmeter (energy meter) is usually used to check the hardware fault
every time it is powered on, and part of the hardware fault can be checked when it
is working normally.The errors shown are divided into two categories: one is the
circuit hardware error message, and the possible questions and solutions are
shown in Table 1.If a problem is found during the power self-test, after entering the
measurement state, the upper left corner of the display will display "* F".You can
repower, view the information displayed, and click the table below to take specific
measures.If the problem persists, contact the company.
The other category is error information about measurement, as shown in Table 2.
The problems and solutions are given in the following two tables.

7.1. Power-on Error Displays and Counter-Measures

The ultrasonic flow meter provides an automatic power-on diagnosis for the
hardware problems. When any message (with the power on) in the following table
displays, counter-measures should be taken.

LCD display
information

Reason

Solution

The program ROM
checksum is incorrect

Illegal or wrong system
ROM

Contact the manufacturer

The data memory is
read and written
incorrectly

Memory parameter data is
incorrect

Power on again/contact the
manufacturer

System data memory
error

System storage data area
error

Power on again/contact the
manufacturer

«
...
56
57
58
59
60
...
»

Содержание MC-SUP2000H






































































Отзывы:

Нет отзывов

Похожие инструкции для MC-SUP2000H

Бренд: Larson Davis Страницы: 193

Бренд: Facom Страницы: 116

Бренд: Omega Engineering Страницы: 22

Бренд: A&D Страницы: 74

Бренд: DAKOTA ULTRASONICS Страницы: 25

Бренд: DAKOTA ULTRASONICS Страницы: 36

Бренд: Kawai Страницы: 66

Бренд: LOVATO ELECTRIC Страницы: 10

Бренд: e-sylife Страницы: 2

Бренд: Omega Страницы: 4

Бренд: Endress+Hauser Страницы: 24

Бренд: FuzzDog Страницы: 6

Бренд: AXE Страницы: 5

VACTEST GCD 200

Бренд: BUSCH Страницы: 12

Бренд: Omega Страницы: 59

Бренд: Z-Wave Страницы: 5

Бренд: Klein Tools Страницы: 20

Бренд: MEWOI Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды