Twilight MC-SUP2000H Скачать руководство пользователя страница 63

Страница: 63 / 69

Chapter 7 Troubleshooting

- 58 -

* Avoid the water flowing

into the pump well forming a

waterfall and rushing down.

Move the sensor to a place

where air bubbles are not

easy to get in.
* The inlet side of the pump.
*Upstream side of the valve.

High turbidity: Higher than

the turbidity of injected

sewage and returned

sludge.

The sensor installation V

method is changed to Z

method.
Move the sensor to the

smaller part of the pipeline

on the same pipeline.
Move the sensor to other

parts or other pipes.
Try the large sensor option.
Move the sensor to the

straight pipe.

A large amount of scale

deposits inside the old

pipe.
Lining peeling: There is a

gap between the lining and

the pipe.
Thicker lining: Due to the

use of mortar lining, the

thickness is more than

tens of millimeters.

The sensor is installed at

the elbow or tapered pipe.

、

The influence of external

noise

Try to shorten the cable

length between the host

and the sensor.

*There is a radio signal

transmitting station nearby.

Содержание MC-SUP2000H






































































Результаты поиска

Содержание MC-SUP2000H

Отзывы:

Бренды по названию

Популярные бренды

Twilight MC-SUP2000H, Руководство пользователя

Результаты поиска

Содержание MC-SUP2000H

Отзывы:

Бренды по названию

Популярные бренды