Tweco FABRICATOR 252i Скачать руководство пользователя страница 32

Страница: 32 / 100

FABRICATOR 252i

INSTALLATION/SETUP

INSTALLATION/SETUP 3-2

Manual 0-5155

50/60 Hz

Single Phase

Primary Supply

Lead Size

Minimum

Primary Current

Circuit Size

(Vin/Iin)

Minimum

Plug Size

Current & Duty Cycle

MIG

LIFT TIG

STICK

Yes

10 AWG

208-230/50A

50A

40% @ 250A 40% @ 250A

40% @ 230A

Table 3-1: Input Power Source Leads for Fabricator 252i

WARNING

ELECTRIC SHOCK

can kill;

SIGNIFICANT DC VOLTAGE

is present after removal of input power.

DO NOT

TOUCH

live electrical parts.

SHUT DOWN

welding power source, disconnect input power employing lockout/tagging procedures. Lock-out/tagging

procedures consist of padlocking line disconnect switch in open position, removing fuses from fuse box, or shutting

OFF and red-tagging circuit breaker or other disconnecting device.

Electrical Input Requirements

Operate the welding power source from a single-phase 50/60 Hz, AC power source. The Welding Power Source must be:

• Correctly installed, if necessary, by a qualified electrician.
• Correctly earthed (electrically) in accordance with local regulations.
• Connected to the correct size power point, fuse and primary supply lead based on Table 3-1.

WARNING

Any electrical work must be carried out by a qualified Electrical Tradesperson.

3.05 Electromagnetic Compatibility

WARNING

Extra precautions for Electromagnetic Compatibility may be required when this Welding Power Source is

used in a domestic situation.

A. Installation and Use - Users Responsibility

The user is responsible for installing and using the welding equipment according to the manufacturer’s instructions.

If electromagnetic disturbances are detected then it shall be the responsibility of the user of the welding equipment to

resolve the situation with the technical assistance of the manufacturer. In some cases this remedial action may be as

simple as earthing the welding circuit, see NOTE below. In other cases it could involve constructing an electromagnetic

screen enclosing the Welding Power Source and the work, complete with associated input filters. In all cases,

electromagnetic disturbances shall be reduced to the point where they are no longer Troublesome.

NOTE

The welding circuit may or may not be earthed for safety reasons. Changing the earthing arrangements

should only be authorized by a person who is competent to assess whether the changes will increase the

risk of injury, e.g. by allowing parallel welding current return paths which may damage the earth circuits

of other equipment. Further guidance is given in IEC 60974-13 Arc Welding Equipment - Installation and

use (under preparation).

Содержание FABRICATOR 252i





































































































Результаты поиска

Содержание FABRICATOR 252i

Отзывы:

Похожие инструкции для FABRICATOR 252i

Бренды по названию

Популярные бренды

Tweco FABRICATOR 252i, Руководство по эксплуатации

Результаты поиска

Содержание FABRICATOR 252i

Отзывы:

Похожие инструкции для FABRICATOR 252i

Бренды по названию

Популярные бренды