Tweco FABRICATOR 252i Скачать руководство пользователя страница 37

Страница: 37 / 100

INSTALLATION/SETUP

FABRICATOR 252i

Manual 0-5155

3-7 INSTALLATION/SETUP

8. Left Digital Display

MIG Mode

This digital meter is used to display the pre-set (preview)

Wirefeed Speed in Inches Per Minute (IPM) in MIG mode

and actual welding amperage of the power source when

welding. At times of non-welding, the digital meter will

display a pre-set (preview) value of Wirefeed Speed. This

value can be adjusted by varying the Left Knob (Control

No 6).

STICK and LIFT TIG Modes

The digital meter is used to display the pre-set (preview)

amperage in STICK / LIFT TIG modes and actual welding

amperage of the power source when welding. At times of

non-welding, the amperage meter will display a pre-set

(preview) value in both STICK and LIFT TIG modes. This

value can be adjusted by varying the Left Knob (Control

No 6).
When welding, this digital meter will display actual welding

amperage in all modes.
At the completion of welding, the digital meter will hold

the last recorded amperage value for a period of approxi-

mately 10 seconds in all modes. The amperage meter will

hold the value until; (1) any of the front panel controls

are adjusted in which case the unit will revert to preview

mode, (2) welding is recommenced, in which case actual

welding amperage will be displayed, or (3) a period of 10

seconds elapses following the completion of welding in

which case the unit will return to preview mode.
The display is also used for providing error messages to

the user and showing other information, which will be

explained in Section 5.

9. Right Digital Display

MIG Mode

This digital meter is used to display the pre-set (preview)

Voltage in MIG mode and actual welding voltage of the

power source when welding. At times of non-welding,

the digital meter will display a pre-set (preview) value of

Voltage. This value can be adjusted by varying the Right

Knob (Control No 7).

STICK and LIFT TIG Modes

This digital meter is used to display the Welding Output

Terminal Voltage in STICK / LIFT TIG modes during non-

welding or welding. This value can not be adjusted by

varying the Right Knob (Control No 7).
When welding, this digital meter will display actual welding

voltage in all modes.
At the completion of welding, the digital meter will hold

the last recorded voltage value for a period of approxi-

mately 10 seconds in all modes. The voltage meter will

hold the value until; (1) any of the front panel controls

are adjusted in which case the unit will revert to preview

mode, (2) welding is recommenced, in which case actual

welding amperage will be displayed, or (3) a period of 10

seconds elapses following the completion of welding in

which case the unit will return to preview mode.
The display is also used for providing error messages to

the user and showing other information, which will be

explained in Section 5.

10. MIG Gun Adaptor

The MIG Gun Adapter is the connection point for the Tweco

Fusion 250A MIG Gun. Refer to section 3.08 for the correct

procedure for attaching the Tweco Fusion 250A MIG Gun.

Содержание FABRICATOR 252i





































































































Результаты поиска

Содержание FABRICATOR 252i

Отзывы:

Похожие инструкции для FABRICATOR 252i

Бренды по названию

Популярные бренды

Tweco FABRICATOR 252i, Руководство по эксплуатации

Результаты поиска

Содержание FABRICATOR 252i

Отзывы:

Похожие инструкции для FABRICATOR 252i

Бренды по названию

Популярные бренды