Tweco FABRICATOR 252i Скачать руководство пользователя страница 41

Страница: 41 / 100

INSTALLATION/SETUP

FABRICATOR 252i

Manual 0-5155

3-11 INSTALLATION/SETUP

TIG

Process

MIG

STICK

If the welder is in Advanced Features mode and the Weld Process Selection button (Control No 3) is pressed, the

welder will exit Advanced Features mode, saving any change made, and change to the next weld process function

in the sequence: MIG, LIFT TIG, STICK. (See previous note) If you wish to view the Advanced Features for the next

process you will need to enter the Advanced Features function again.

ARC CONTROL

Right Knob

If the welder is in Advanced Features mode and the right knob (Control No 7) is pressed for one (1) second (to enter

Arc Control Function) the welder will exit Advanced Features mode, saving any change made, and enter the Arc Control

Function for the currently selected weld process.

MIG (GMAW/FCAW)Mode Advanced Features Menu Map

RUN- / IN

POST / FLOW

BURN / BACK

WIRE / SHRP

Advanced Menu – MIG

Mode

Wire Feed Speed

ARC- / TYPE

MIG / CNTL

PRE- / FLOW

SPOT

STCH

DWEL / TIME

ON OFF

*STCH / TIME

AUTO CV

Advanced Menu - MIG

Options or Range

Press Advanced Button

to Exit to Welding Mode

LOCL REMT

0.1 - 5.0 S

MPM IPM

WFS- / UNIT

30 - 150%

0.0 - 30.0 S

0.00 - 1.00 S

0.1-20.0 S

FACT / DFLT

*SPOT / TIME

0.2 - 4.0 S
0.1 - 1.0 S

0.0 - 9999.9

NO YES

Press Advanced Button

to Exit to Welding Mode

Left Display

Right Display

ON OFF

Left Knob Selection

* SPOT TIME and STCH TIME are only active when SPOT or STCH are “ON”.

Note “SPOT” and “STCH” are MUTUALLY EXCLUSIVE functions. If the user enables either function and the system

detects that the OTHER function is already ON, the system will automatically turn the OTHER conflicting function OFF.

Left Display: Where (2) items shown, e.g. RUN- / IN, the display will alternate (flash) between the (2) items

Right Knob Selection

Art # A-10505_AB

TIG

Process

MIG

STICK

Advanced

Features

Figure 3-5: MIG Advanced Menu

Содержание FABRICATOR 252i





































































































Результаты поиска

Содержание FABRICATOR 252i

Отзывы:

Похожие инструкции для FABRICATOR 252i

Бренды по названию

Популярные бренды

Tweco FABRICATOR 252i, Руководство по эксплуатации

Результаты поиска

Содержание FABRICATOR 252i

Отзывы:

Похожие инструкции для FABRICATOR 252i

Бренды по названию

Популярные бренды