Tweco FABRICATOR 252i Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 100

background image

WARRANTY SCHEDULE

5 Years Parts* / 3 Years Labor

ArcMaster, Excelarc, Fabricator, Fabstar, PowerMaster

Portafeed, Ultrafeed, Ultima 150, WC 100B

* 5 years on the Original Main Power Transformer and Inductors not mounted on PCBoards.

* 3 years on Power Supply Components

2 Years Parts and Labor Unless specified

Auto-Darkening Welding Helmet (electronic Lens), ** 1 Month Harness Assy

Victor Regulator for Fabricator 181i (No labor)

1 Years Parts and Labor Unless specified

95S, Water recirculators

All Plasma Welding consols (i.e WC-1 Controller, WT Timer,

WF-100 Capstain Feeder, etc)

180 days parts and Labor Unless specified

Plasma Welding Torch and leads packages

Gas Regulators "Supplied with power sources" (No Labor)

90 days parts / No Labor

Remote Controls

MIG and TIG Torches (Supplied with power sources)

Replacement repair parts

30 days parts / No Labor

MIG Torch for Fabricator 181i

5-2-1 years Parts / No Labor

FirePower® Welders

5 Years Parts / No Labor

Victor® Professional

Victor Technologies limited warranty shall not apply to:

Consumable Parts for MIG, TIG, Plasma welding, Plasma cutting and Oxy fuel torches, O-rings, fuses, filters or other parts that fail due
normal wear

* Warranty repairs or replacement claims under this limited warranty must be submitted by an authorized Victor Technologies repair facility
within thirty (30) days of the repair.

* No employee, agent, or representative of Victor Technologies is authorized to change this warranty in any way or grant any other warranty,
and Victor Technologies shall not be bound by any such attempt. Correction of non-conformities, in the manner and time provided herein,
constitutes fulfillment of Victor Technologies’s obligations to purchaser with respect to the product.

* This warranty is void, and seller bears no liability hereunder, if purchaser used replacement parts or accessories which, in Victor
Technologies's sole judgment, impaired the safety or performance of any Victor Technologies product. Purchaser’s rights under this warranty
are void if the product is sold to purchaser by unauthorized persons.

«
...
97
98
99
100
»

Содержание FABRICATOR 252i





































































































Отзывы:

Нет отзывов

Похожие инструкции для FABRICATOR 252i

Бренд: Samsung Страницы: 127

Бренд: OMA Страницы: 73

Бренд: D3D Страницы: 4

Бренд: Harman Страницы: 10

Gemini GEM-X255

Бренд: NAPCO Страницы: 40

Бренд: NAPCO Страницы: 16

Бренд: NAPCO Страницы: 6

Бренд: Yamaha Страницы: 7

Бренд: ESAB Страницы: 21

Бренд: EAW Страницы: 2

IQ PANEL 2 PLUS

Бренд: QOLSYS Страницы: 2

Бренд: Gabarron Страницы: 16

Бренд: Elk Products Страницы: 3

ATT COMBI LIFT 4.40 S

Бренд: Nussbaum Страницы: 260

Бренд: Roadstar Страницы: 23

Бренд: NAIM Страницы: 51

Бренд: Miller Страницы: 20

Genie BBSKETDL15B-1001

Бренд: Terex Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды