Turner Cyclops 6K, Руководство пользователя, Страница: 7 / 21

Cyclops Submersible Sensor
998-2100 Rev. 2.9 Page 7
2.4 Functional Test for Cyclops with connector
To perform a functional check on the Cyclops, connect the Pigtail colored wires
to the power supply and multi-meter as shown in Figure 1 below.
Additional Equipment required for functional tests:
DC Power Supply, 3 - 15 VDC, >100 mA
Multi-meter to read 0
– 5 VDC
Note: Supply voltages greater than 15 VDC will result in damage to
the sensor.
Figure 1.
With the Cyclops connected as shown in Figure 1 answer questions 1-3 by
making the following functional tests:
1. Is the LED on?
Hold a piece of white paper about ½ an inch in-front of the optical head to
ensure the LED is on.
Note: Cannot perform this test for Turbidity
sensors because they use IR which is not visible.
2. Is there voltage output?
The multi-meter should be reading some voltage >0 VDC
3. Does the voltage output change?
Move the light source closer to your hand or a surface and check if the
voltage output increases
Cyclops Pigtail cable holes
3
6
4
2
1
5 5
2
4 4
6
1
3
Cyclops pins / wires
3
4
2
1
5
6 6
Cyclops Pigtail cable holes
3
6
4
2
1
5 5
2
4 4
6
1
3 3 3
6 6
4 4
2 2
1
5 5 5
2
4 4
6
1
3
Cyclops pins / wires
3
4
2
1
5
6 6
Cyclops pins / wires
3
4
2
1
5
6 6
3
4
2
1
5
6 6
3 3
4 4
2 2
1
5 5
6 6
Cyclops Pigtail cable holes
3
6
4
2
1
5 5
2
4 4
6
1
3 3 3
6 6
4 4
2 2
1
5 5 5
2
4 4
6
1
3
Cyclops pins / wires
3
4
2
1
5
6 6
Cyclops pins / wires
3
4
2
1
5
6 6
3 3
4 4
2 2
1
5 5
6 6
Cyclops Pigtail cable holes
3 3
6 6
4 4
2 2
1
5 5 5
2
4 4
6
1
3 3 3
6 6
4 4
2 2
1
5 5 5
2
4 4
6
1
3
Cyclops pins / wires
3
4
2
1
5
6 6
3
4
2
1
5
6 6
3 3
4 4
2 2
1
5 5
6 6
Cyclops pins / wires
3
4
2
1
5
6 6
3 3
4 4
2 2
1
5 5
6 6
3 3
4 4
2 2
1
5 5
6 6
3 3
4 4
2 2
1
5 5
6 6
12.00 .015
+ -
DC Power Supply
PSU Positive Connection
(Red)
Supply Ground
0 VDC (Black)
3.52
Multimeter
10 VDC
+
-
Signal Output
“+” (White)
Analog Ground
“-” (Green)
Blue
(Tie to Green for 10X)
Brown
(Tie to Green for 100X)
X1(Low) Gain
Leave both wires disconnected
for Functional Check
Cyclops Pigtail Cable
12.00 .015
+ -
DC Power Supply
12.00 .015
+ -
DC Power Supply
PSU Positive Connection
(Red)
Supply Ground
0 VDC (Black)
3.52
Multimeter
10 VDC
+
-
3.52
Multimeter
10 VDC
+
-
Signal Output
“+” (White)
Analog Ground
“-” (Green)
Blue
(Tie to Green for 10X)
Brown
(Tie to Green for 100X)
X1(Low) Gain
Leave both wires disconnected
for Functional Check
Cyclops Pigtail Cable