turck 6814035 Скачать руководство пользователя страница 22

Страница: 22 / 77

Address Setting for Spanner Modules

Hans Turck GmbH & Co. KG | T +49 208 4952-0 | F +49 208 4952-264 | [email protected] | www.turck.com

Factory Reset (F_Reset), Switch Position "900"

F_Reset (Reset to factory setting)

Switch position: 900

This mode sets all device-settings back to the default values and deletes all data in the device's inter-
nal flash.

Set Button

The Set button is placed left to the rotary coding switches under the cover at the device.

Pushing the Set-button causes a device-restart

NOTE

Setting 900 is no operation mode! Please set the device to another mode after having
reset the IP address to the default values.

ATTENTION!

Protective cover opened
Protection class IP65/IP67/IP69K not guaranteed



Screw the protective cover over the rotary coding-switches firmly



Check if seal of the protective cover is correctly placed

Fig. 12: Set button

ATTENTION!

Protective cover opened
Protection class IP65/IP67/IP69K not guaranteed



Screw the protective cover over the rotary coding-switches firmly



Check if seal of the protective cover is correctly placed

x 10

x 1

x 100

x 10

x 1

x 100

Содержание 6814035














































































Результаты поиска

Содержание 6814035

Отзывы:

Похожие инструкции для 6814035

Бренды по названию

Популярные бренды

turck 6814035, Руководство по началу работы

Результаты поиска

Содержание 6814035

Отзывы:

Похожие инструкции для 6814035

Бренды по названию

Популярные бренды