Turbosound TBV118L-AN Скачать руководство пользователя страница 45

Страница: 45 / 50

Rigging Manual

11.0.1 Required Components

Item

Quantity

M10 x 40 mm

2 (minimum)

TBV123

As required

TBV118L

As required

11.0.2 Measured Weights

Item

Quantity

Weight

TBV118L

37.0 kg

81.6 lbs

TBV123

22.0 kg

48.5 lbs

TBV118L-AN

38.5 kg

84.9 lbs

TBV123-AN

23.0 kg

50.7 lbs

11.0.3 Maximum Quantities

Maximum allowed quantities and system weights for 10:1, 7:1 and 5:1 design

factors. Ensure that eyebolts are specified with sufficient WLL to support the

system weight at the desired design factor. It is recommended to check local

regulations regarding design factor requirements in order to comply with

regional codes.

10:1 Design Factor Eyebolt Suspension - Passive Or Powered

TBV118L-AN

TBV123-AN

System

115.5 kg

123.0 kg

107.5 kg

92.0 kg

Weight

254.6 lbs

271.2 lbs

237.0 lbs

202.8 lbs

7:1 Design Factor Eyebolt Suspension - Passive Or Powered

TBV118L-AN

TBV123-AN

System

192.5 kg 200.0 kg 184.5 kg 192.0 kg 176.5 kg 138.0 kg

Weight

424.4 lbs 440.9 lbs 406.7 lbs 423.3 lbs 389.1 lbs 304.2 lbs

5:1 Design Factor Eyebolt Suspension - Passive Or Powered

TBV118L-AN

TBV123-AN

System

231.0 kg 215.5 kg 223.0 kg 207.5 kg 192.0 kg 176.5 kg 161.0 kg

Weight

509.3 lbs 475.1 lbs 491.6 lbs 457.5 lbs 423.3 lbs 389.1 lbs 354.9 lbs

Chapter 11: Using Eyebolts

The various arrays shown in this manual may be flown using 2 eyebolts instead of

the TBV123-FB flybar.
The recommended eyebolt is M10, with a thread greater than 18 mm, and a

working load limit adequate for the size of the specific array to be suspended.
Third party eyebolts must be specified and supplied by authorised,

qualified personnel.
The system is flown with 2 two eyebolts securely attached to the threaded holes

in the top surface of the uppermost TBV123 cabinet or TBV118L subwoofer.

Two threaded holes are also provided on the bottom surface. These can be used

with eyebolts for tether points, or for flying the systems inverted.

WARNING

DO NOT EXCEED THE QUANTITY OF TBV118L SUBWOOFERS OR TBV123 CABINETS

SHOWN IN 11.0.3 THE TABLE OF MAXIMUM QUANTITIES. FAILURE TO FOLLOW

INSTRUCTIONS MAY CAUSE PERMANENT INJURY OR DEATH.

DO NOT EXCEED A MAXIMUM 2-LEG BRIDLE HITCH ANGLE OF 60 DEGREES FOR

SINGLE POINT SUSPENSION CONFIGURATIONS. FAILURE TO FOLLOW INSTRUCTIONS

MAY CAUSE PERMANENT INJURY OR DEATH.

11.0.4 Personnel

The following procedures shall be undertaken by experienced, certified,

qualified, and authorised personnel only. The procedures require the use of three

or more authorised persons.

Protective Headwear shall be worn

Protective Footwear shall be worn

Protective Gloves shall be worn

Protective Eyewear shall be worn

Practice Safe Lifting

Содержание TBV118L-AN



















































Результаты поиска

Содержание TBV118L-AN

Отзывы:

Похожие инструкции для TBV118L-AN

Бренды по названию

Популярные бренды

Turbosound TBV118L-AN, Руководство по монтажу

Результаты поиска

Содержание TBV118L-AN

Отзывы:

Похожие инструкции для TBV118L-AN

Бренды по названию

Популярные бренды