7
other factors affecting the power tool work safety. If any
damage to the power tool is detected, it should be repaired
before use.
Improper power tool maintenance is a reason for many
accidents.
f)
Cutting tools should be sharp and clean.
Keeping sharp cutting
edges in good condition reduces the risk of jamming and facilitates
operation.
g)
Power tools, equipment, working tools etc. should be used
according to this user's manual taking into account operating
conditions and the work to be done.
Misusing a power tool can
result in dangerous situations.
h)
At low temperatures and after a long brakes in operation it is
recommended to turn the power tool to operate it with no load
for a few minutes to provide proper grease distribution inside
its driving mechanism.
i)
Use soft, damp (cannot be wet) cloth and soap to clean power
tools. Do not use petrol, solvents and other agents that may
damage your equipment
.
j)
Power tools can be stored/carried after making sure that all
moving components are locked and protected against release
with original devices intended for this purpose.
k)
Store power tools in a dry, dust and water-protected place.
l)
Carry your power tool in its original packaging to provide
protection against mechanical damage.
m)
Keep handles and grip surfaces clean and free from oil and
grease.
Secure grip and control over the tool in unexpected
circumstances are impossible if handles and grip surfaces are slippery.
running faster than their rated speed can break and fly apart.
d
)
The outside diameter and the thickness of your accessory
must be within the capacity rating of your power tool.
Incorrectly sized accessories cannot be adequately guarded or
controlled
.
e
)
The arbour size of wheels, flanges, backing pads or any other
accessory must properly fit the spindle of the power tool.
Accessories with arbour holes that do not match the mounting
hardware of the power tool will run out of balance, vibrate excessively
and may cause loss of control.
f
)
Do not use a damaged accessory. Before each use inspect the
accessory such as abrasive wheels for chips and cracks,
backing pad for cracks, tear or excess wear, wire brush for
loose or cracked wires. If power tool or accessory is dropped,
inspect for damage or install an undamaged accessory. After
inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory
and run the power tool at maximum no-load speed for one
minute.
Damaged accessories will normally break apart during this
test time.
g
)
Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety glasses.
As appropriate, wear dust mask, hearing protectors, gloves
and workshop apron capable of stopping small abrasive or
workpiece fragments.
The eye protection must be capable of
stopping flying debris generated by various operations . The dust mask
or respirator must be capable of filtrating particles generated by your
WARNING! General warnings regarding the use of
operation. Prolonged exposure to high intensity noise may cause
power tools.
hearing loss.
Repair
:
h
)
Keep bystanders a safe distance away from work area.
Anyone entering the work area must wear personal
protective equipment.
Fragments of workpiece or of a broken
accessory may fly away and cause injury beyond immediate area of
operation.
i
)
Hold power tool by insulated gripping surfaces only, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord.
Cutting accessory
contacting a "live" wire may make exposed metal parts of the power
tool "live" and shock the operator.
j
)
Position the cord clear of the spinning accessory.
If you lose
control, the cord may be cut or snagged and your hand or arm may be
ANGLE GRINDER
pulled into the spinning accessory.
Safety Warnings Common for Grinding, Sanding,
k
)
Never lay the power tool down until the accessory has
come
Wire Brushing, Polishing or Abrasive Cutting-Off
to a
complete stop.
The spinning accessory may grab the surface
Operations:
and pull the power tool out of your control.
a)
This power tool is intended to function as a grinder, sander,
l
)
Do not run the power tool while carrying it at your side.
wire brush, polisher or cut-off tool. Read all safety warnings,
Accidental contact with the spinning accessory could snag your
instructions, illustrations and specifications provided with
clothing, pulling the accessory into your body.
this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
m
)
Regularly clean the power tool's air vents.
The motor's fan will
draw the dust inside the housing and excessive accumulation of
b
)
Do not use accessories which are not specifically designed
powdered metal may cause electrical hazards.
and recommended by the tool manufacturer.
Just because the
accessory can be attached to your power tool, it does not assure safe
n
)
Do not operate the power tool near flammable materials.
operation.
Sparks could ignite these materials.
c
)
The rated speed of the accessory must be at least equal to
o
)
Do not use accessories that require liquid coolants.
Using
the maximum speed marked on the power tool.
Accessories
water or other liquid coolants may result in electrocution or shock.
a)
Warranty and post-warranty repairs of its power tools are
carried out by PROFIX Service, which guarantees the best
quality or repair and use of genuine spare parts.
b)
Under no circumstances repair damaged batteries. All
activities related to battery repair may be performed only by
the manufacturer or by authorised service centres.
WARNING!
While operating power tools it is necessary to observe basic
work safety rules to avoid fire, electric shock or mechanical
injury.
Содержание TJS40
Страница 2: ...2 A 0 1 20V 20V 2 3 4 5 6 7 8 11 12 9 10 7 B ...
Страница 3: ...E D 1 2 3 3 C 7 11 20 V 20 V ...
Страница 71: ...71 ...
Страница 72: ......
