TRW TA S40 Series Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 60

background image

GROUP 0603-V-003-0207

STEERING

7

DocID

TRW TAS STEERING GEAR

Page 1-9

Review Draft

8

General Design

Integral Power Steering

TAS power steering gears are another part of our fully integral
hydraulic power steering gear family. Fully integral hydraulic power
steering means that the gear contains a manual steering mechanism, a
hydraulic control valve, and a hydraulic power cylinder, all in a single,
compact package.

Rotary Control Valve

The rotary control valve combines simplicity of construction with desir-
able performance characteristics. The speed at which the driver can
turn the steering wheel with power assist is dependent upon the pump
ﬂow (measured in gallons per minute or liters per minute) directed to
a cylinder cavity. The control valve controls ﬂow through the steering
gear.

The pressure (measured in pounds per square inch, or bar) required for
the gear to steer the vehicle is created by the power steering pump to
overcome resistance at the steered wheels. The control valve senses
these requirements and directs ﬂuid to the appropriate cylinder cavity
in the steering gear (and in the auxiliary cylinder if it is a dual steering
system) at the proper ﬂow rate and pressure.

Pressure Means Work, Flow Means Speed

The higher pressure a steering gear can withstand, the more work it
can perform. The maximum operating pressure for TAS40, 55, 65 and
85 gears is 2,175 psi (150 bar). The maximum operating pressure for
a TAS66 gear is 2,320 psi (160 bar). Maximum ﬂow rate for all TAS
gears is 8 gal/min (30.3 L/min).

The TAS series gears can steer a vehicle within its front-end weight
rating through a turn at low speed and engine idle. As the driver turns
the steering wheel faster or slower, more or less ﬂuid will be required
by the gear. TAS series vehicle front-end weight ratings are as follows:

Gear

Front Axle Rating

TAS40

9,000 lb (4,100 kg)

TAS55

12,000 lb (5,400 kg)

TAS65

14,300 lb (6,500 kg)

TAS66

14,300 lb (6,500 kg)

TAS85

18,000 lb (8,200 kg)

The recommended minimum ﬂow at 1

1

⁄

2

steering wheel turns per

second is as follows:

Gear

Minimum Flow Rate

TAS40

2.2 gal/min (8.3 L/min)

TAS55

2.6 gal/min (9.8 L/min)

TAS65

3.0 gal/min (11.4 L/min)

TAS66

3.0 gal/min (11.4 L/min)

TAS85

3.6 gal/min (13.6 L/min)

If the steering gear valve is controlling an auxiliary cylinder, increased
minimum ﬂow is required (generally at least 75%) based on the size of
the auxiliary cylinder and the vehicle's steering geometry.

Maximum internal leakage for all TAS gears is 1 gal/min.

«
...
7
8
9
10
11
...
»

Содержание TA S40 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для TA S40 Series

Бренд: panel Страницы: 27

Бренд: Maple Systems Страницы: 2

Бренд: sauter Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды