manualshive.com logo in svg

TRW TA S40 Series, Руководство по обслуживанию, Страница: 28 / 60

Поделиться
Скачать
TRW TA S40 Series Скачать руководство пользователя страница 28

Page 1-28 

TRW TAS STEERING GEAR

DocID

STEERING

GROUP 0603-V-003-0207 

File Last Modified: September 17, 2012 10:18 am

27

Remove relief 
valve components

Remove dirt & 
water seal

15. 

If equipped, remove relief valve cap (5), o-ring (6) and two-piece 
relief valve (7) from the valve housing.  Discard the o-ring.

16. 

Remove and discard the dirt & water seal (2) from the input 
shaft (19).  Save this seal for comparison with the new seal.

7

⁄

8

"

 Socket

Clean input shaft

Remove valve 
housing bolts

17. 

Clean any paint or corrosion from the exposed area of the input 
shaft.

18. 

Remove the four torx head valve housing bolts (1).

Fine grade 
  emery cloth

Torx socket 
  E-16 or E-18

Remove valve 
housing, worm and 
rack subassembly

19. 

Be prepared for more fluid drainage and remove the rack piston 
subassembly.  Place the assembly on a clean cloth.  For the 
TAS85 it may help to rotate the input shaft to move the rack 
piston toward the lower end of the housing.  This will force the 
valve housing to exit the main housing.

 

The set position of poppet seat and  

 

sleeve assemblies (23) must not be 

disturbed if the poppets are not going to be replaced or 
reset during disassembly.

Содержание TA S40 Series





























































Отзывы:

Нет отзывов