TRW TA S40 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 60

TRW TA S40 Series Скачать руководство пользователя страница 29

GROUP 0603-V-003-0207

STEERING

7

DocID

TRW TAS STEERING GEAR

Page 1-29

Review Draft

28

20.

Remove and discard the valve housing seal rings (11 & 12).

Remove seals

Pocket knife

If your gear is short "V"

construction, the rack piston seal is on

the end of the rack piston farthest from the input shaft. Re-
move the seal before removing the valve housing assembly to
prevent the Teﬂon rack piston seal ring (27) from "hanging up"
when it exits the housing. Expose the seal through the sector
shaft cavity, then cut and remove the seal ring from the rack
piston.

Do not remove the input shaft,

valve worm assembly or balls from

the rack piston until the ball return guides are removed
as damage to the ball guides will occur.

Remove ball return
guide cap/strap

21.

Remove and discard the two special sealing screws (29). Remove
the ball return cap (31) and seal (32), or strap (30), discard the
seal.

5

⁄

32

"

Allen

wrench or T-30
Torx wrench

Remove ball return
guides

22.

Make sure the rack piston is on a cloth so the steel balls that
fall out won't roll very far. Remove ball return guide halves (33)
by carefully inserting a screwdriver between the rack piston and
guides.

Left hand ball return guide halves are

copper or zinc chromate plated for

identiﬁcation and right hand guides are not plated.

RETAIN THE GUIDES FOR REASSEMBLY

.

Screwdriver

19A.

Remove ball return
guide clip

21A. Bend down the two tabs (tangs) that are against the hex head

bolts. Remove two bolts and the clip. Discard the clip.

1/2" Socket

OR

«
...
27
28
29
30
31
...
»

Содержание TA S40 Series





























































Отзывы:

Нет отзывов