TRW TA S40 Series Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 60

background image

Page 1-2

TRW TAS STEERING GEAR

DocID

STEERING

GROUP 0603-V-003-0207

File Last Modified: September 17, 2012 10:18 am

1

Hazard Warning Deﬁnitions

A warning describes hazards or unsafe practices which could result in

severe personal injury or death.

A caution describes hazards or unsafe practices which could result in

personal injury or product or property damage.

A note gives key information to make following a procedure easier or quicker.

Disclaimer

This Service Manual has been prepared by TRW Commercial Steering Systems for reference and use
by mechanics who have been trained to repair and service steering components and systems on heavy
commercial vehicles. TRW Commercial Steering Systems has exercised reasonable care and diligence to
present accurate, clear and complete information and instructions regarding the TRW Commercial Steer-
ing TAS Series Integral Power Steering Gears. Since this is a general Service Manual, the photographs
and illustrations may not look exactly like the steering gear being serviced. The procedures, therefore ,
must be carefully read and understood before servicing.

If inspection or testing reveals evidence of abnormal wear or damage to the TAS steering gear or if you
encounter circumstances not covered in the Manual,

Stop - Consult the vehicle manufacturer's

Service Manual and warranty. Do not try to repair or service a TAS steering gear which has
been damaged or includes any part that shows excessive wear unless the damaged and worn
parts are replaced with original TRW replacement and service parts and the unit is restored to
TRW's speciﬁcations for the TAS steering gear.

It is the responsibility of the mechanic performing the maintenance, repairs or service on a particular TAS
steering gear to (a) inspect the steering gear for abnormal wear and damage, (b) choose a repair proce-
dure which will not endanger his/her safety, the safety of others, the vehicle, or the safe operation of
the vehicle, and (c) fully inspect and test the TAS steering gear and the vehicle steering system to ensure
that the repair or service of the steering gear has been properly performed and that the steering gear and
system will function properly.

Patents

TRW Commercial Steering Division TAS power steering gears are covered by several United States and
foreign patents, either issued or pending.

© TRW Inc., 2007

«
1
2
3
4
...
»

Содержание TA S40 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для TA S40 Series

Бренд: InTouch Страницы: 4

Raptor VeeCAN 800

Бренд: New Eagle Страницы: 26

Бренд: Tangent Страницы: 40

Бренд: Voyager Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды