Description:
Quick Start Guide
HMC3102A-M
Specifications:
The HMC3102A-M is a combination operator-based HMI (Human
Machine Interface) with built-in PLC (Programmable Logic
Controller) operation. It communicates with external PLCs over
serial communications ports to read/write data. Five I/O
expansion modules can be attached.
Power:
24VDC +/- 15%, 25W (with 5
expansions)
Display:
10.2” TFT (800 x 480 pixels)
Color graphics display
Bezel:
NEMA 4X (IP 66) rated
Touchscreen:
4-wire analog resistive
LEDs:
Power indicator
CPU:
32-bit RISC, 454 MHz
Port Details (COM1 and COM2):
HMC3102A-M 800x480 pixels, 10.2” color TFT, with five
expansion slots.
Contents:
—
1 HMC3102A-M (in plastic bag with protective cover sheet
on the screen)
—
1 plastic bag containing 4 mounting clamps (each clamp
Memory:
45 MB Max. Application Memory
Serial Comms (DE9S):
Two serial ports
(RS232/RS485/RS422)
USB Slave (Micro Type B):
Upload/download projects
USB Host (Standard Type A): Data storage
Ethernet (RJ45):
10/100 Mbps
SD card:
Micro SD (high capacity- 4 to 32
DB9S (Female) Connector
Note: connect shell to shield of cable.
Grounding:
The HMC3102 should have a good electrical connection to earth
ground via the power connector for safety and to reduce electrical
noise. The HMC unit should be grounded separately from other
consisting of cap nut, bolt, and clamp)
—
1 three prong green power plug*
—
Cardboard package inserts
Expansion ports:
Operating temp:
GB)
Five for optional HMC3 I/O
modules
0 to 60° C
high-power systems.
—
Quick Start Guide
*Note: Connector manufacturer may vary.
Programming software (MAPware-7000), cables, and power
supply purchased separately.
Panel Mounting and Panel Cutout:
HMC3102A-M
Tighten the mounting screws evenly to a torque between 0.4 Nm to
maintain water and dust resistance. Make sure the panel is not dirty
Humidity:
10% to 90% (non-condensing)
Dimensions (WxHxD):
10.55 x 7.48 x 1.30 inches
[268.0 x 190.0 x 33.0mm]
Panel cutout:
10.07 x 7.01 inches
[256.0 x 178.0mm]
Mounting Module to Panel:
Step 2: Tighten clamps evenly to prevent warping. Continue to
tighten until a torque force of 0.4-0.5 Nm is obtained.
Step 3: HMC3102 should be aligned evenly with the cutout with
no warping present after clamps are tightened.
Note: Do not use a ground connection that has potential
impedance (such as painted screws) or is subject to vibration.
Expansion I/O Modules:
The HMC3102A-M has five expansion slots that you can use to
connect I/O modules. Below is a listing of modules currently
available (consult Maple Systems website for additional
information).
HMC3-M1616P:
16 digital input, 16 PNP-type digital
output
HMC3-M1614Y:
16 digital input, 14 digital output
(12 relay, 2 PNP-type)
HMC3-M1212P0200:
12 digital input, 12 PNP-type digital
output, 2 analog input
HMC3-M1212Y0200:
12 digital input, 12 digital output
(10 relay, 2 PNP-type), 2 analog
input
HMC3-M1210P0201:
12 digital input, 10 PNP-type digital
output, 2 analog input and 1 analog
output.
HMC3-M1210Y0201:
12 digital input, 10 digital output (8
relay, 2 PNP-type), 2 analog input,
and warped and that it is strong enough to hold the unit.
Note: Maximum Panel thickness (on which unit is to be mounted)
should be 6.0 mm (Tolerance: +/-0.2 mm).
HMC3-M0808P0401T:
and 1 analog output.
8 digital input, 8 PNP-type digital
output, 4 analog input and 1 analog
output.
HMC3-M0808Y0401T:
8 digital input, 8 digital output (6
relay, 2 PNP-type), 4 analog input,
and 1 analog output.
Doc. No. 1011-0303
Maple Systems, Inc. 808 134th St SW, Suite 120, Everett, WA 98204-7333 www.maplesystems.com
Rev 02, 11/29/2018
