truflo TSMP Series Скачать руководство пользователя | Manualshive

Страница: 7 / 67

background image

Revision

8

–

November

2011

7

GENERAL PRECAUTIONS

WARNING

A pump is a pressure vessel with rotating parts that can be hazardous.    Hazardous fluids may be contained by
the pump including high temperature, flammable, acidic, caustic, explosive, and other risks. Operators and
maintenance personnel must realize this and follow safety measures.    Personal injuries will result if procedures
outlined in this manual are not followed. Truflo Pumps will not accept responsibility for physical injury, damage
or delays caused by a failure to observe the instructions in this manual and the IOM provided with your
equipment.

General Precautions

NOTE

NEVER HEAT TO REMOVE IMPELLER. It may explode due to trapped
liquid.

NOTE

NEVER use heat to disassemble pump due to risk of explosion from tapped liquid.

NOTE

NEVER operate pump without coupling guard correctly installed.

NOTE

NEVER run pump below recommended minimum flow when dry, or without
prime.

NOTE

ALWAYS lock out power to the driver before performing pump maintenance.

NOTE

NEVER operate pump without safety devices installed.

NOTE

NEVER operate pump with discharge valve closed.

NOTE

NEVER operate pump with suction valve closed.

NOTE

DO NOT change service application without approval of an authorized Truflo
Pumps representative.

NOTE

Safety Apparel

:

Insulated work gloves when handling hot bearings or using

bearing heater , Heavy work gloves when handling parts with sharp edges,
especially impellers Safety glasses (with side shields) for eye protection Steel-toed
shoes for foot protection when handling parts, heavy tools, etc. Other personal
protective equipment to protect against hazardous/toxic fluids.

NOTE

Receiving:

Assembled pumping units and their components are heavy. Lift

properly and support equipment, neglect can result in serious physical injury
and/or equipment damage. Lift equipment only at specifically identified lifting
points or as instructed in the current IOM. Current manuals are available at

www.truflo.com

or contact your local Truflo Pumps sales representative. Note:

Lifting devices (eyebolts, slings, spreaders, etc.) must be rated, selected, and used
for the entire load being lifted.

WARNING

Alignment:

Shaft alignment procedures must be followed to prevent catastrophic

failure of drive components or unintended contact of rotating parts. Follow
coupling manufacturer’s coupling installation and operation procedures.

«
...
5
6
7
8
9
...
»

Содержание TSMP Series




































































Отзывы:

Нет отзывов

Похожие инструкции для TSMP Series

Бренд: Danfoss Страницы: 12

Бренд: ICP Страницы: 9

Бренд: Eaton Страницы: 29

Бренд: EAS Electric Страницы: 165

PELLEMATIC SmartXS

Бренд: MAINE ENERGY SYSTEMS Страницы: 82

Aerco AM Series

Бренд: Watts Страницы: 7

Бренд: Underhill Страницы: 2

Бренд: Gude Страницы: 62

Бренд: Little Giant Страницы: 8

Бренд: Liberty Pumps Страницы: 16

FLEXFLO A-100NE

Бренд: Blue-White Страницы: 28

INSTANT-FLOW MICRO MIX Series

Бренд: Chronomite Страницы: 2

BC-F20HWR2-200L

Бренд: enertik Страницы: 33

Бренд: Walrus Pump Страницы: 12

JABSCO 18670 Series

Бренд: Xylem Страницы: 16

Бренд: THERMEx Страницы: 36

Бренд: Raider Страницы: 92

Бренд: ITS Telecom Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды