Trotec TDP 370 E, Оригинальное руководство пользователя, Страница: 3 / 17

EN 3 deep well pump TDP 370 E / TDP 750 E
• Before carrying out maintenance, care or repair work on
the device, remove the mains plug from the mains socket.
Hold onto the mains plug while doing so.
• When positioning the device, observe the minimum
distances from walls and other objects as well as the
storage and operating conditions specified in the Technical
data chapter.
• Do not remove any safety signs, stickers or labels from the
device. Keep all safety signs, stickers and labels in legible
condition.
General safety warnings – Electrical safety
• The device is to be supplied with a rated residual current
of no more than 30 mA by means of an RCD (Residual
Current protective Device).
• Ensure that all electric cables outside of the device are
protected from damage (e.g. caused by animals). Never
use the device if electric cables or the power connection
are damaged!
• The electrical connection must correspond to the
specifications in chapter Technical data.
• Insert the mains plug into a properly secured mains
socket.
• Switch the device off and disconnect the power cable from
the mains socket when the device is not in use.
• Do not under any circumstances use the device if you
detect damages on the mains plug or power cable.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Defective power cables pose a serious health risk!
• Should the connection line of the device be damaged, it
must be replaced by the manufacturer, his customer
service or similarly qualified personnel in order to avoid
hazards.
• Should there be a risk of flooding, install the plug
connections in a flood-proof area.
There is a risk of
electric shock!
• Make sure that the mains voltage corresponds to the
specifications on the nameplate.
• Have all electrical installations carried out by an expert
according to the national regulations and the device-
specific requirements.
• Do not use the power cable to drag the device.
• Hold onto the mains plug while pulling the power cable out
of the mains socket.
• Protect the power supply cable against heat, oil and sharp
edges. Make sure that the power supply cable is not
crushed, kinked or subjected to other mechanical stresses.
• Only use splash-proof extension cables intended for
outdoor use whilst observing the device's power input.
Before using cable drums, always unroll the cable
completely. Check the cable for damage. The use of
extension cables which are not approved for outdoor use
can result in injuries due to electric shock.
• Before performing any work on the device, in case of leaks
in the water system, before taking work breaks or when
not in use, remove the mains plug from the mains socket.
General safety warnings – Personal safety
• Never use the device with persons or animals in the water
or pumping medium or if they could access it.
There is a
risk of electric shock!
• Never insert any objects or limbs into the device.
• This appliance is not a toy! Keep away from children and
animals. Do not leave the device unattended during
operation.
Device-specific safety warnings for deep well
pumps
• Only operate the device in an upright position.
• Keep in mind, that lubricants are used within the device.
These might potentially cause damages or contaminations
if emitted. Do not use the device for drinking water or in
garden ponds with either a fish population or valuable
plants.
• Do not carry the device by holding it at the connection
cable or hose. Do not fasten it there either.
• Do not place any objects on the device – not even to
weight it down. The device will sink to the ground due to
its own weight.
• After the set-up of the device, its mains plug must be
readily accessible during operation.
• Prevent dry running of the device! Before start-up the
device must be completely submerged in the pumping
medium.
• Wear sturdy shoes to protect yourself against electric
shock.
• Before taking the device into operation, have the following
checked by an expert:
– earthing, neutral conductor and RCD must be
functioning properly and correspond to the national
regulations,
– electrical plug connections must be protected from
moisture.
• Provide appropriate frost protection.