TrojanLabel Trojan 3 Скачать руководство пользователя страница 18

Страница: 18 / 91

TrojanThree User Guide

Page | 17

Remove the printhead from the foil bag.

Remove the orange protective plastic cover from the printhead cartridge. Holding the printhead

cartridge by the handle

Release the flaps covering the ink ports

Release the clip retaining the cover near the center of the printhead cartridge

Carefully remove the protective cover

Remove the protective strip from the electrical contacts. While holding the printhead cartridge by

the handle with one hand, grasp the pull tab with the other hand and, slowly and carefully, peel

back the plastic strip covering the electrical contacts.

NOTE:

Dispose of the removed strip immediately and do not allow the removed strip to contact

the electrical contacts.

Remove the protective strip from the printhead nozzles. While holding the printhead cartridge by

the handle with one hand, grasp the pull tab with the other hand and slowly and carefully peel

back the plastic strip covering the printhead nozzles. Maintain an angle of no less than 45° with

the printhead surface when pulling on the strip.

Содержание Trojan 3




























































































Результаты поиска

Содержание Trojan 3

Отзывы:

Похожие инструкции для Trojan 3

Бренды по названию

Популярные бренды

TrojanLabel Trojan 3, Руководство пользователя

Результаты поиска

Содержание Trojan 3

Отзывы:

Похожие инструкции для Trojan 3

Бренды по названию

Популярные бренды