18
version. After that the Mobile Station switches to
the locomotive list. The last locomotive used will
be displayed. For starter sets this is the locomo-
tive that comes with the set. The locomotive can
be taken into the operating menu by pressing
once on the control knob, or another locomotive
can be selected.
The STOP Button
The STOP Button stops all locomotives and
powered rail cars immediately and bypasses any
braking delay set on them. There is no power in
the track. Pressing the STOP Button again will
start all locomotives and powered rail cars again
in the last operating state (speed, direction, func-
tions on, etc.) set on them.
The Operating Menu
Locomotive operations take place in the opera-
ting menu. Moreover, this menu is divided into the
main menu and the locomotive list. The locomo-
tive currently called up is shown in the display.
The desired speed for the locomotive can be
set by turning the control knob. Pressing on the
control knob will reverse the direction of travel;
the speed at which the locomotive was previously
being run is not transferred to the new direction
of travel. The locomotive remains stopped, and
with DCC any braking delay set on locomotives is
bypassed.
The Display
If the locomotive has a name assigned to it, this
name is displayed.
On all other locomotives the protocol, the
address, and then the speed level, preceded by
„F“, is displayed.
The headlights / marker lights can be turned on
and off with the headlights / marker lights button.
When operating locomotives with special func-
tions, these functions can be turned on and off
with the function buttons F1 through F8.
Pressing once on the OK button switches the
Mobile Station to the locomotive list. This is indi-
cated by the menu symbol in the display.
Pressing once on the ESC button switches the
Mobile Station to the main menu. Here you can
select the desired submenu by turning the control
knob. Pressing once on the control knob will call
up the submenu shown in the display. Pressing
once on the ESC button will take you out of the
submenu.
The Locomotive List
The locomotive list is divided up into several areas
to make selecting a locomotive to be controlled
more manageable. When the locomotive list has
been called up, the different areas are offered; an
area can be selected by turning the control knob
and can be called up by pressing once on the
control knob. The following areas are offered:
• SX1 LOC
Selection area for Selectrix1 locomotives and
powered rail cars with the addresses 00 to 99
• SX2-1 LOC
Selection area for Selectrix2 locomotives and
powered rail cars with the addresses 00 to
9999
• SX2-2 LOC
Selection area for Selectrix2 locomotives and
powered rail cars with the addresses 00 to
9999; when changes are made in the speed,
each „click“ on the control knob corresponds
to a change of 2 speed levels.
• SX2-4 LOC
Selection area for Selectrix2 locomotives and
powered rail cars with the addresses 00 to
9999; when changes are made in the speed,
each „click“ on the control knob corresponds
to a change of 4 speed levels.
• DCC-S 14F
Selection area for DCC locomotives and po-
wered rail cars with a short address (01 - 127)
and 14 speed levels
• DCC-S 28F
Selection area for DCC locomotives and po-
wered rail cars with a short address (01 - 127)
and 28 speed levels
• DCC-S 126F
Selection area for DCC locomotives and po-
wered rail cars with a short address (01 - 127)
and 126 speed levels
• DCC-L 28F
Selection area for DCC locomotives and
powered rail cars with a long address (0001
- 9999) and 28 speed levels
• DCC-L 126F
Selection area for DCC locomotives and
powered rail cars with a long address (0001
- 9999) and 126 speed levels
• NAMES
Selection area for locomotives and powered
rail cars that have names assigned to them.
The locomotives and powered rail cars from
the starter sets are also listed here.
