background image

2

TABLE OF CONTENTS

SECTION I DESIGN

For The System Design Engineer

      

                 Page

1. General Description ...................................................................................................................................... 3
2. System Design and Floor Layout ................................................................................................................ 3
3. Outdoor Installations .................................................................................................................................... 4

SECTION II INSTALLATION

For The Installing Contractor

1. Unpack and Inspect....................................................................................................................................... 4
2. Assemble Framework ................................................................................................................................... 4
3. Attach Adjoining Ductwork .......................................................................................................................... 4
4. Install Ionizing-Collecting Cells ................................................................................................................... 5
5. Install Air By-Pass Baffles............................................................................................................................ 5
6. Connect Drain ................................................................................................................................................ 5
7. Mount Controller............................................................................................................................................ 5
8. Complete Wiring ............................................................................................................................................ 5

A. High Voltage Wiring .................................................................................................................................. 5

    B. Primary Wiring .......................................................................................................................................... 5
9. Check Out For System Start-Up................................................................................................................... 6

SECTION III OPERATION AND SERVICE

For The Maintenance Engineer

1. Introduction and Principle of Operation ..................................................................................................... 6
2. General Description ...................................................................................................................................... 6
3. Initial Start-up ................................................................................................................................................ 6
4. Routine Maintenance .................................................................................................................................... 7
5. Periodic Maintenance ................................................................................................................................... 7
6. Troubleshooting ............................................................................................................................................ 8
7. Spare Parts..................................................................................................................................................... 9
8. Troubleshooting Reference Chart ............................................................................................................. 10
Pages 11-14........................................................................................................................................NOT USED

SECTION IV REFERENCE

Illustrations and Drawings

Figure 1

Single Unit Outline............................................................................................. 15

Figure 1A

Dimensional and Specification Data................................................................ 16

 

Figure 2

Exploded View of Single Section unit ............................................................. 17

Figure 3

Recommended Foundation and Drain Basin Design..................................... 18

Figure 4

NOT USED .......................................................................................................... 19

Figure 5

Structural Framework Assembly...................................................................... 20

Figure 6

Cell Arrangement and Bus Bar Connections.................................................. 21

Figure 6A

Diagram of Bus Bar Connections .................................................................... 22

Figure 6B

Diagram of Bus Bar Connections .................................................................... 23

Figure 7

Model 60 Cell Assembly.................................................................................... 24

Figure 8

Model 60 Air Baffle Arrangement ..................................................................... 25

Figure 8A

Diagram of Air Baffle Arrangement.................................................................. 26

Figure 9

NOT USED .......................................................................................................... 27

Figure 10

NOT USED .......................................................................................................... 28

Figure 11

Control Schematic (Supplied with specific unit configuration).................... 29

Figure 12

Field Wiring (Supplied with specific unit configuration) ............................... 30

Figure 13

Access Door Electrical Interlock Arrangement .............................................. 31

Figure 14A

High Voltage Cell Termination.......................................................................... 32

Figure 14B

NOT USED .......................................................................................................... 32

Figure 15

High Voltage Lead Termination at Power Supply........................................... 33

Содержание AIR BOSS 60 Series






























Отзывы: