Trilogy Communications Mentor RG 360-00-05 Скачать руководство пользователя страница 36

Страница: 36 / 121

Page 36 of 121

Trilogy Communications

Mentor RG

5.6.5

AES Tone Sub- menu

Tone

Frequency

CH 1

< 25Hz - 20kHz >

CH 2

< 25Hz - 20kHz >

CH 3

< 25Hz - 20kHz >

CH 4

< 25Hz - 20kHz >

Amplitude

CH 1

< -120 - 0 dBFS >

CH 2

< -120 - 0 dBFS >

CH 3

< -120 - 0 dBFS >

CH 4

< -120 - 0 dBFS >

Mode

Channels 1-2

Off
On

CCIR

EBU

Lip Sync

Channels 3-4

As Ch 1-2

Direction

Channels 1-2

Std

Reverse

Channels 3-4

As Ch 1-2

Four simultaneous AES Groups are available from both the mainboard outputs and the

360-20-00 HD/3G-SDI option board if fitted.

The factory default setting for each Group is for the embedded AES to be enabled “On”. However,

the factory default setting is for the Tone Mode to be “Off”, which means the tones are initially set

to silence and should be configured using the Tone Mode menu to the right of this page.

Setting the Group Enable mode to “Off” will remove Tones and Source Ident from the stream,

regardless of any settings in the Tone Mode sub-menu.

Setting Tone mode to “Off” mutes the signal but retains the AES data within the stream. Setting

Tone Mode to “On” will provide continuous tone.

Содержание Mentor RG 360-00-05


























































































































Результаты поиска

Содержание Mentor RG 360-00-05

Отзывы:

Trilogy Communications Mentor RG 360-00-05, Руководство пользователя, Страница: 36 / 121

Результаты поиска

Содержание Mentor RG 360-00-05

Отзывы: