Trigon Electronics MiniGuard IID, Инструкции по установке и программированию

Страница: 8 / 17

Page 8
Miniguard IID
PROGRAMMING (Continued)
(G) Entering Cards:
This function requires the installation of the Card Reader
Interface option and a card reader. Card access makes it
possible for the user to use an access card at the unit and
gain entry. Each card entered is converted to a standard
4 digit Entry Code and goes into “Direct Entry Code
memory”.
1. Unit must be in Program Mode (see section A).
2. Enter “# 1”. (You are in 'Batch Mode).
3. Pass a card through the card reader.
You will hear one beep.
This indicates card number accepted. Three 'beeps'
indicates card not accepted.
For next card repeat step 3 until all cards are done.
Note: If 3 beeps are heard, that card cannot be used
because it already appears in memory. Batch Mode is
terminated on this or any fault.
4. Press “#” when card programming is complete,
to return to main Program Mode.
5. Enter "# #" to exit Program Mode, otherwise,
continue programming by entering the desired
function code.
(H) Deleting Cards:
If the 4 digit value assigned to the card is known, it can
be removed from memory with the same procedure as
Deleting Entry Codes. Otherwise, from Program Mode:
1. Unit must be in Program Mode (see section A).
2. Press“#2” and pass the card to be deleted
through the reader.
You will hear one beep.
This indicates successful removal.
Note: Three beeps indicates that the card was not in
memory, and the Batch Mode is aborted.
3. Press “#2” to re-enter Batch Mode.
- or -
If the card has been successfully removed
4. Press“#” to return to normal Program Mode
then, continue programming by entering the
desired function code.
5. Enter "# #" to exit Program Mode, otherwise,
continue programming by entering the desired
function code.
(I) Programming Site Identification Code:
In the case of multi-unit installations, the Site
Identification Code makes it possible for the party
receiving a call from a Miniguard IID to identify which
“gate” is calling.
1. Unit must be in Program Mode (see section A).
2. Enter "# 8" and the 4 digit number.
You will hear two beeps.
3. Enter "# #" to exit Program Mode, otherwise,
continue programming by entering the desired
function code.
(J) Programming Tamper Code:
This feature can be used to alert a manager if the unit is
being tampered with. (Four unsuccessful or invalid
attempts to enter the programming mode constitutes a
tamper.) The unit looks up the Resident Code stored in
“tamper” and dials the phone number associated with
that resident code.
1. Unit must be in Program Mode (see section A).
2. Enter " # 6" and the Resident Code that you
have chosen.
You will hear two beeps.
3. Enter "# #" to exit Program Mode, otherwise,
continue programming by entering the desired
function code.
(K) Programming Time-of-Day Clock:
The time of day clock allows automatic operation of
the output relay.
1. Unit must be in Program Mode (see section A).
2. Enter " # 3 " .
3. Enter the Month. (01=Jan., 02=Feb.,... 12=
Dec).
Be sure to include the zeros when setting the
clock.
4. Enter the Monthly Date. (01 thru 31).
5. Enter the last two digits of the Year
(i.e., 1995
would be 95).
6. Enter the Hour.
Use military time; 00 thru 23 hrs.
7. Enter the Minutes. (00 thru 59).
8. Enter the Day of Week. (1= Mon., 2=Tues, ...
7=Sun.).
You will hear two beeps.
Note: A military time format (24 hour clock) is used
clock programming .
9. Enter "# #" to exit Program Mode, otherwise,
continue programming by entering the desired
function code.